KEPCO KLP 10-150-2 Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 92

background image

3-36

KLP070312

With the power supply configured as shown in Figure 3-15 and assuming the load causes the
power supply to operate in voltage mode, varying external resistor R2 from 0 to 10K causes the
output voltage of the power supply to vary linearly from 0 to full scale, while R1 can be used to
adjust the current limit. When the power supply operates in current mode, R2 will adjust the volt-
age limit and R1 will adjust output current.

Factory default full scale (F.S.) resistance programming is 10K ohms based on F.S. program-
ming voltage of 10V. To set full scale resistance to a lower value, see PAR. 4.3.3 to change the
F.S. programming voltage to a lower value, then adjust based on 1000 ohms/Volt.

3.4.3

PROGRAMMING WITH EXTERNAL VOLTAGE

Figure 3-16 is a simplified diagrams of the KLP showing the switch configuration and external
connections required for analog programming using an external voltage.

1. Virtual Model (PAR. 3.2.8) and Overvoltage and Overcurrent settings (PAR. 3.4.4) must be

established via either local programming or digital remote programming prior to initiating
Analog Remote programming.

2. Turn off power and configure the Analog I/O DIP switch (Figure 2-2) as follows:

SW1: OFF (Program output voltage via voltage)
SW2: OFF (Program output current via voltage)
SW3: either OFF or ON (disabled when in remote analog programming mode; see

Table 2-2)

SW4: Reserved - Do not use
SW5: Either OFF (Local controls enabled) or ON (Local controls locked)

3. Configure Analog I/O Port J2 (Figure 2-2) by referring to Table 2-7 and Figure 3-16 (ground-

ing J1 pin 12 enables analog programming).

4. Refer to PAR. 3.4.4 to change overvoltage or overcurrent setting in analog programming

mode.

With the power supply configured as shown in Figure 3-16 and assuming the load causes the
power supply to operate in voltage mode, varying source voltage V2 from 0 to maximum causes
the output voltage of the power supply to vary linearly from 0 to full scale, while V1 can be used
to adjust the current limit. When the power supply operates in current mode, V2 will adjust the
voltage limit and V1 will adjust output current.

Factory default full scale (F.S.) voltage programming is 10V. To set full scale voltage program-
ming to a lower value, see PAR. 4.3.3

«
...
74
75
76
77
78
...
»

Содержание KLP 10-150-2





























































































Отзывы:

Нет отзывов

Похожие инструкции для KLP 10-150-2

Бренд: Vacon Страницы: 6

Бренд: 80% Arms Страницы: 12

Бренд: Parkside Страницы: 640

Бренд: Parkside Страницы: 60

Бренд: Chicago Pneumatic Страницы: 3

PSI 9040-120 2U

Бренд: EPS Stromversorgung Страницы: 91

Бренд: Pyramid Страницы: 4

Бренд: VOLTCRAFT Страницы: 8

Бренд: Parkside Страницы: 28

Бренд: LEYBOLD Страницы: 3

Бренд: Parkside Страницы: 258

Бренд: VONROC Страницы: 84

Бренд: Wacker Neuson Страницы: 44

Бренд: Toolson Страницы: 136

Бренд: Whelen Engineering Company Страницы: 2

Бренд: Wacker Neuson Страницы: 144

Бренд: Ryobi Страницы: 2

Бренд: POWER ON BOARD Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды