KEPCO KLP 10-150-2 Скачать руководство пользователя страница 51

Страница: 51 / 92

KLP070312

3-11

4. To change the configuration tap the

DC OUTPUT

switch once. The

DC VOLTS

and

AMPERES

start blinking.

• Specify either

SERI

(series configuration for higher voltage) or

PARA

(parallel configura-

tion for higher current) using either the

VOLTAGE

CURRENT

control by

holding in

and rotating the control. Both connected units must be set the same, either

SERI

PARA

• Specify the total number of units in the configuration to 2 by rotating the

CURRENT

con-

trol.

• Specify the unit number to be assigned (2 = slave) by rotating the

VOLTAGE

control.

5. Press

DC OUTPUT

to accept the displayed settings. The unit briefly flashes wait, then

restarts with the new settings; press

FUNCTION

to abort without changing the settings.

NOTE: Until both units are configured properly, the displays will cycle as follows: status display

will flash

E241

(hardware error), then

DC VOLTS,

status display

and

DC AMPERES

flash

where

= unit number and

= total number of units, the status display

flashes the type of connection

SERI

(series) or

PARA

(parallel).

3.2.13.2 CONFIGURE POWER SUPPLY AS MASTER [STANDARD MODELS ONLY]

1. Turn power on. If the unit comes up in setpoint mode (see PAR. 3.2.6), tap either the

CUR-

RENT

VOLTAGE

controls to take the unit out of setpoint mode (status display goes from

SET

to blank).

2. Using a thin tool (e.g., a paper clip), press the

FUNCTION

switch once, then rotate either the

CURRENT

VOLTAGE

control until the display reads

M/S

3. Tap the

DC OUTPUT

switch.

• The status display reads either

SERI

(series) or

PARA

(parallel).

• The

DC VOLTS

display shows the number assigned to the unit (1 = master, 2 or above =

slave).

• The

DC AMPERES

display shows the maximum number of units in the configuration.

• The factory default is standalone operation (

DC VOLTS

and

DC AMPERES

show

4. To change the configuration tap the

DC OUTPUT

switch once. The

DC VOLTS

and

AMPERES

start blinking.

• Specify either

SERI

(series configuration for higher voltage) or

PARA

(parallel configura-

tion for higher current) using either the

VOLTAGE

CURRENT

control by

holding in

and rotating the control. Both connected units must be set the same, either

SERI

PARA

• Specify the total number of units in the configuration to 2 by rotating the

CURRENT

con-

trol.

• Specify the unit number to be assigned (1 = master) by rotating the

VOLTAGE

control.

Содержание KLP 10-150-2





























































































Результаты поиска

Содержание KLP 10-150-2

Отзывы:

Похожие инструкции для KLP 10-150-2

Бренды по названию

Популярные бренды

KEPCO KLP 10-150-2, Руководство пользователя

Результаты поиска

Содержание KLP 10-150-2

Отзывы:

Похожие инструкции для KLP 10-150-2

Бренды по названию

Популярные бренды