KEPCO KLP 10-150-2 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 92

background image

228-1353 SAFETY - (SWITCH) 070312

C/(D BLANK)

SAFETY INSTRUCTIONS

1. Installation, Operation and Service Precautions

This product is designed for use in accordance with EN 61010-1 and UL 3101 for Installation Category 2,
Pollution Degree 2. Hazardous voltages are present within this product during normal operation. The prod-
uct should never be operated with the cover removed unless equivalent protection of the operator from
accidental contact with hazardous internal voltages is provided:

2. Grounding

This product is a Class 1 device which utilizes protective earthing to ensure operator safety.

3. Electric Shock Hazards

This product outputs hazardous voltage and energy levels as a function of normal operation. Operators
must be trained in its use and exercise caution as well as common sense during use to prevent accidental
shock.

There are no operator serviceable parts or adjustments within the product enclosure.
Refer all servicing to trained service technician.

Source power must be removed from the product prior to performing any servicing.

The PROTECTIVE EARTHING CONDUCTOR TERMINAL must be properly con-
nected prior to application of source power to the product (see instructions on instal-
lation herein) in order to ensure safety from electric shock.

PROTECTIVE EARTHING CONDUCTOR TERMINAL - This symbol indicates the
point on the product to which the protective earthing conductor must be attached.

EARTH (GROUND) TERMINAL - This symbol is used to indicate a point which is
connected to the PROTECTIVE EARTHING TERMINAL. The component installer/
assembler must ensure that this point is connected to the PROTECTIVE EARTH-
ING TERMINAL.

CHASSIS TERMINAL -This symbol indicates frame (chassis) connection, which is
supplied as a point of convenience for performance purposes (see instructions on
grounding herein). This is not to be confused with the protective earthing point, and
may not be used in place of it.

This symbol appears adjacent to any external terminals at which hazardous voltage
levels as high as 600V d-c may exist in the course of normal or single fault condi-
tions.
This symbol appears adjacent to any external terminals at which hazardous voltage
levels in excess of 600V d-c may exist in the course of normal or single fault condi-
tions

!

!

!

!

«
...
3
4
5
6
7
...
»

Содержание KLP 10-150-2





























































































Отзывы:

Нет отзывов

Похожие инструкции для KLP 10-150-2

Бренд: Navitar Страницы: 6

Бренд: Makita Страницы: 6

Бренд: Makita Страницы: 14

Бренд: Makita Страницы: 7

Бренд: Makita Страницы: 13

Бренд: Makita Страницы: 4

Бренд: Makita Страницы: 5

Бренд: Makita Страницы: 17

Бренд: Makita Страницы: 3

Бренд: Makita Страницы: 12

Бренд: Makita Страницы: 3

Бренд: Makita Страницы: 3

Бренд: Makita Страницы: 16

Бренд: Makita Страницы: 3

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 16

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды