KEPCO KLP 10-150-2 Скачать руководство пользователя страница 53

Страница: 53 / 92

KLP070312

3-13

3.2.13.4 RESTORING THE MASTER/SLAVE CONFIGURATION TO STANDALONE OPERATION

[STANDARD MODELS ONLY]

First configure the master, then the slave for standalone operation.

1. If the units are in setpoint mode (see PAR. 3.2.6), tap either the

CURRENT

VOLTAGE

controls to take the units out of setpoint mode (status display goes from

SET

to blank).

2. Using a thin tool (e.g., a paper clip), press the

FUNCTION

switch of the unit to be restored to

standalone operation, then rotate either the

CURRENT

VOLTAGE

control until the display

reads

M/S

3. Tap the

DC OUTPUT

switch once.

• The status display reads either

SERI

(series) or

PARA

(parallel).

• The

DC VOLTS

display shows the number assigned to the unit (1 = master). The

AMPERES

display shows the maximum number of units in the configuration.

4. To change the configuration tap the

DC OUTPUT

switch once. The

DC VOLTS

and

AMPERES

start blinking.

• Rotate the

CURRENT

control until

DC AMPERES

display shows

• Rotate the

VOLTAGE

control until

DC VOLTS

display shows

5. Press

DC OUTPUT

to accept the displayed settings. The unit briefly flashes

WAIT

, then

restarts with the new settings; press

FUNCTION

to abort without changing the settings.

NOTE: Once the master is configured for standalone operation, the slave status display will

flash

E241

(hardware error).

6. Repeat steps 2 through 5 to restore the slave unit to standalone operation.

3.2.14

LAN INTERFACE CONFIGURATION [E-SERIES MODELS ONLY]

Using a thin tool (e.g. end of paper clip), press

FUNCTION

switch once, then rotate either

VOLTAGE

CURRENT

control until status display reads

LAN

. Press

DC OUTPUT

switch to

enter the LAN Interface configuration menu. Rotate either

VOLTAGE

CURRENT

control to

see the available functions.

•

LRST

- LAN Reset. To restore the LAN interface configuration to the factory default, tap

DC OUTPUT

switch once, then rotate either

VOLTAGE

CURRENT

control to show

YES

in the

DC VOLTS

display, then tap

DC OUTPUT

switch again. The factory default

settings listed in PAR. 3.3.1.3 are restored upon exiting the Function menu.

Содержание KLP 10-150-2





























































































Результаты поиска

Содержание KLP 10-150-2

Отзывы:

Похожие инструкции для KLP 10-150-2

Бренды по названию

Популярные бренды

KEPCO KLP 10-150-2, Руководство пользователя

Результаты поиска

Содержание KLP 10-150-2

Отзывы:

Похожие инструкции для KLP 10-150-2

Бренды по названию

Популярные бренды