KEPCO KLP 10-150-2 Скачать руководство пользователя страница 84

Страница: 84 / 92

4-6

KLP 070312

The main panel status display shows calibration, and the voltage and current meters are not
visible.

FIGURE 4-1. CALIBRATION WINDOW

7. Use the computer keyboard to enter the password in the text box displaying the word PASS-

WORD, then press the ENTER key.

8. If password is correct, the status display on the VXI main panel reads CAL and the buttons

on Calibration Screen (Figure 4-1) are enabled (highlighted). If the password is incorrect, the
password text box displays “WRONG #”. Repeat step 7 to enter the correct password, or
click the

Calibrate Close

button on the VXI main panel to exit calibration.

NOTE: Calibrations may be done in any order.

9. Proceed to PAR. 4.4.1 for voltage calibration, PAR 4.4.2 for current calibration., PAR. 4.4.3

for external calibration or PAR. 4.4.4 to exit calibration

4.4.1

VOLTAGE CALIBRATION (VXI

plug&play

DRIVER DEMO)

During voltage calibration, the voltage, voltage readback and remote analog voltage readback
are calibrated.

1. Click the

VOLTAGE

button on the Calibration window to start voltage calibration: the Voltage

Calibration Window (Figure 4-2) appears. Minimum voltage is first; the status display on both
the UUT and the VXI main panel) reads

V_0

. Monitor DVM and click the “+” button to

Содержание KLP 10-150-2





























































































Результаты поиска

Содержание KLP 10-150-2

Отзывы:

Похожие инструкции для KLP 10-150-2

Бренды по названию

Популярные бренды

KEPCO KLP 10-150-2, Руководство пользователя

Результаты поиска

Содержание KLP 10-150-2

Отзывы:

Похожие инструкции для KLP 10-150-2

Бренды по названию

Популярные бренды