KEPCO KLP 10-150-2 Скачать руководство пользователя страница 45

Страница: 45 / 92

KLP070312

3-5

FIGURE 3-1. FUNCTION SWITCH MENU STRUCTURE

3.2.5

ENABLING/DISABLING OUTPUT POWER

When the power supply is turned on, the output is automatically disabled (

DC OUTPUT

LED is

off) and the

DC VOLTS

and

DC AMPERES

displays show the programmed output voltage and

current set points and the status display reads

SET

To disable the output, press and release the

DC OUTPUT

switch again. The

DC OUTPUT

indi-

cator goes off.

While in the setpoint mode (Status display reads

SET

) the output cannot be turned on (pressing

DC OUTPUT

has no effect). If output was on while setpoint mode was entered, pressing

OUTPUT

will disable the output.

For setpoint adjustment refer to PAR. 3.2.9.2. To enable/disable the output using analog control,
refer to PAR. 3.4.1.

FUNCTION––––––––VIRT* (PAR. 3.2.8)

–––CNFG (PAR 3.2.15)––––VERS

–– MODL

–– Options

–– RTN

         –––ADDR (PAR 3.2.11)
         –––BAUD ***(PAR 3.2.12)
         –––M/S *** (PAR 3.2.13)––– SERI ––––– 1OF2

––2OF2

–– PARA–––– 1OF2

––2OF2

–––LAN ** (PAR 3.2.14)–––––LRST

–––DHCP
–––[AUTO
–––MAC1/MAC2/MAC3
–––IP1/IP2
–––MSK1/MSK2
–––GTE1/GTE2
–––DNS1/DNS2
–––RTN

–––UTIL (PAR 3.2.16)––––––RELY (PAR 3.2.16.1)–––––FLT––––––––NORM

––– V->C

––– C->V

–––EXIT

––– RTN

––MAN

––LIST

––RTN

–––QkBt (PAR 3.2.16.2)
–––ADJ (PAR 3.2.4)
–––SYST (PAR 3.2.16.3)––––rINH *

* PASSWORD REQUIRED.

–––RCOV *–––––OVP

** E-SERIES MODELS ONLY.

––– OCP

*** STANDARD MODELS ONLY.

–––RTN

––– OLF

–––ANRB (PAR 3.2.16.4)

––– TEMP

–––ANPR (PAR 3.2.16.5)

––– PWR

–––LBT ***

––– RTN

–––CAL * (PAR 4.1)

–––RTN

Содержание KLP 10-150-2





























































































Результаты поиска

Содержание KLP 10-150-2

Отзывы:

Похожие инструкции для KLP 10-150-2

Бренды по названию

Популярные бренды

KEPCO KLP 10-150-2, Руководство пользователя

Результаты поиска

Содержание KLP 10-150-2

Отзывы:

Похожие инструкции для KLP 10-150-2

Бренды по названию

Популярные бренды