Jacobsen Fairway 250 JGZZ250 Скачать руководство пользователя страница 80

Страница: 80 / 99

en-78

ADJUSTMENTS

9.11

AIR SUSPENSION SEAT (GRAMMER MSG75 -521) ________________________

9.11.1 WEIGHT ADJUSTMENT ______________________________________________

To adjust the seat for the driver weight, pull or press the
lever for the seat weight adjustment with the driver on
the seat.

The driver weight is adjusted correctly when the arrow is
in the center clear area of the view window.

Within this view area, you adjust the specified height of
the driver to its minimum spring movement.

When you reach the minimum/maximum weight, you
hear the adjustment reach the upper or lower end stop.

The setting for each driver weight must be checked and
adjusted before the vehicle can be driven safely.

To prevent damage to the compressor during the weight adjustment, the compressor must be operated for less
than 1 minute.

9.11.2 FRONT AND BACK ADJUSTMENT _____________________________________

To release the front and back adjustment, lift the locking lever.

WARNING! Risk of accident!
Do not operate the locking lever when you drive.

WARNING! Risk of injury!
When you operate the lever, touch the lever at the grip
section. Do not reach back under the lever.

After the adjustment, the locking lever must lock into the
correct position with an audible click. The seat will not
move into another position if the lever has locked
correctly.

Do not lift the locking lever with your upper or lower leg.

Содержание Fairway 250 JGZZ250




































































































Результаты поиска

Содержание Fairway 250 JGZZ250

Отзывы:

Похожие инструкции для Fairway 250 JGZZ250

Бренды по названию

Популярные бренды

Jacobsen Fairway 250 JGZZ250, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Fairway 250 JGZZ250

Отзывы:

Похожие инструкции для Fairway 250 JGZZ250

Бренды по названию

Популярные бренды