Jacobsen Fairway 250 JGZZ250 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 99

background image

en-80

9

ADJUSTMENTS

9.11.6 ARMRESTS * ** ____________________________________________________

The armrests can fold away and adjustments can be made
to the height of each armrest.

To adjust the armrests for height, separate the round cap
(see the arrow) from the cover. Loosen the hexagon nut
(size 13 mm) below the cover. Adjust the armrests to the
correct position (5-steps) and tighten the nut again.

Replace the cap above the nut.

* If

Installed

** Optional

Accessory

9.11.7 ARMREST ADJUSTMENT * ___________________________________________

To change the angle of the armrests, turn the adjustment
knob.

The front part of the armrest is lifted when you turn the knob
to the outside (+).
The armrest is lowered when you turn the knob to inside (-).

* If

Installed

** Optional

Accessory

9.11.8 BACKREST ADJUSTMENT

To loosen the notches of the backrest adjustment, move the
locking lever to the upper position.

After the adjustment, the locking lever must lock into the
correct position. The backrest will not move into another
position if the lever has locked correctly.

For the best ergonomic use, adjust the backrest within the
range of –5 to +30 degrees (15 steps of 2.5 degrees each).

«
...
80
81
82
83
84
...
»

Содержание Fairway 250 JGZZ250




































































































Отзывы:

Нет отзывов

Похожие инструкции для Fairway 250 JGZZ250

Бренд: Jacobsen Страницы: 76

Бренд: Jacobsen Страницы: 76

Бренд: Jacobsen Страницы: 144

AR-522 jossa ROPS

Бренд: Jacobsen Страницы: 56

AR-522 jossa ROPS

Бренд: Jacobsen Страницы: 115

Бренд: Jacobsen Страницы: 130

Бренд: Jacobsen Страницы: 118

Greens King IV Plus

Бренд: Jacobsen Страницы: 108

Бренд: Jacobsen Страницы: 168

Бренд: Jacobsen Страницы: 166

Бренд: Jacobsen Страницы: 184

Бренд: Jacobsen Страницы: 32

Бренд: Jacobsen Страницы: 98

Greensmaster 3150 04358

Бренд: Toro Страницы: 48

Бренд: Barbieri Страницы: 2

Бренд: Yard-Man Страницы: 42

Бренд: Simplicity Страницы: 14

Бренд: Yard-Man Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды