Jacobsen Fairway 250 JGZZ250 Скачать руководство пользователя страница 46

Страница: 46 / 99

en-45

OPERATION

7.1

DAILY INSPECTION ____________________________________________________

Do a visual inspection of the vehicle and look for indication of wear, loose hardware. Check for any

components that are not included on the machine or damaged. Check for fuel and oil leaks to make sure

that all connections are tight. Make sure that all hoses and tubes are in good condition.

Check the fuel supply, radiator coolant level, crankcase oil level and air cleaner is clean. All fluids must be

at the full mark with the engine cold.

Make sure all cutting units are adjusted to the same height of cut.

Check all tyres for the correct pressure.

Test the operator presence and safety interlock system.

CAUTION

The Inspection Must Be Done Each day
When The Engine Is Turned Off And All

Fluids Are Cold. Lower The Cutter

Equipment To The Ground, Engage the

Parking Brake, Stop the Engine And

Remove the Ignition Key.

Содержание Fairway 250 JGZZ250




































































































Результаты поиска

Содержание Fairway 250 JGZZ250

Отзывы:

Похожие инструкции для Fairway 250 JGZZ250

Бренды по названию

Популярные бренды

Jacobsen Fairway 250 JGZZ250, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Fairway 250 JGZZ250

Отзывы:

Похожие инструкции для Fairway 250 JGZZ250

Бренды по названию

Популярные бренды