Jacobsen Fairway 250 JGZZ250 Скачать руководство пользователя страница 70

Страница: 70 / 99

en-69

MAINTENANCE & LUBRICATION

8.8

AIR CLEANER________________________________________________________

How To Clean The Air Filter

NOTE:After the filter element is cleaned six times, replace
the filter.

(a)

Lift the engine cover.

(b)

Remove the end cap of air filter cartridge.

(c)

Remove the loose dirt from the filter element with

compressed air. Work from the clean to dirty side

with compressed air at a maximum of 6 bar, with the

nozzle 5 cm from the filter element.

(d)

Fit the filter element back into the machine and press

tightly against the rear shoulder.

(e)

Replace the end cap and fasten in position with clips.

Change air filter

(a)

Lift the engine cover.

(b)

Remove the end cap of air filter cartridge.

(c)

Remove all the dust or dirt on the filter.

(d)

Remove the filter element (A). Pull the filter straight and tightly.

(e)

Install a new filter element. Press tightly against the rear shoulder.

(f)

Replace the end cap and fasten in position with clips.

NOTE: An air cleaner that does not allow enough air to go through can damage the engine.

8.9

BATTERY____________________________________________________________

(a)

Keep the fluid levels above battery plates.

(b)

Make sure that there is no corrosion on the battery

post.

WARNING

The batteries make gas that is explosive and

contains corrosive acid. The electrical current is

high enough to cause injuries and burns.

WARNING

The battery posts, terminals and related

accessories contain lead and lead compounds.

CLEAN YOUR HANDS AFTER YOU TOUCH

THESE COMPONENTS

WARNING

Wear the eye protection equipment when you

service the battery.

CAUTION

Discard Used Batteries As Shown In Local

Safety Regulations

Содержание Fairway 250 JGZZ250




































































































Результаты поиска

Содержание Fairway 250 JGZZ250

Отзывы:

Похожие инструкции для Fairway 250 JGZZ250

Бренды по названию

Популярные бренды

Jacobsen Fairway 250 JGZZ250, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Fairway 250 JGZZ250

Отзывы:

Похожие инструкции для Fairway 250 JGZZ250

Бренды по названию

Популярные бренды