Jacobsen Fairway 250 JGZZ250 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 99

background image

en-41

6

CONTROLS

6.8

JOYSTICK UNIT LIFT/LOWER CONTROL (FAIRWAY 405) ________________

NOTE: The joystick will not operate unless the mow
switch (see 6.13 (item G)) is turned on.

The joystick can move in 4 directions (2-Axis) A, B, C
and D.

A

Move the joystick one time to lower all three of the

cutting units.

B

Move the joystick one time to lift all three of the

cutting units. (Hold in position ‘B’ to lift the units into

the transport position)

C

Move the joystick one time to lift unit 7 (left cutting unit).

D

Move the joystick one time to lift unit six (right hand cutting unit).

NARROW-CUT CONTROL
When switch 'G' is held in position 'F', units six and seven lift together.

When switch 'G' is in position 'E', units six and seven are disconnected and any additional movements of the
joystick can control only the units 1 to 5.

6.9

HYDRAULIC LIFT LEVER (FAIRWAY 250 AND 305) ______________________

The cutting units are lifted and lowered by the control
lever (A) on the right hand side of the operators seat.
The control lever is operated as follows:
To lift: Move the lever backward and hold in position until
the units are at the needed height.
To lower: Move the lever forward and hold in this
position, the units lower to ground level. The lever
automatically returns to the neutral position on release.

NOTE: When any unit is moved out of work the cutting
unit blades do not rotate when lowered until the foot
switch is operated.

A

B

C

D

F

G

E

«
...
40
41
42
43
44
...
»

Содержание Fairway 250 JGZZ250




































































































Отзывы:

Нет отзывов

Похожие инструкции для Fairway 250 JGZZ250

Бренд: Texas Страницы: 28

Бренд: ECLOZ Страницы: 56

Бренд: LawnMaster Страницы: 40

Бренд: Snapper Страницы: 28

Бренд: Yard-Man Страницы: 5

Бренд: Gardol Страницы: 324

Бренд: Yard-Man Страницы: 8

Бренд: Ransomes Страницы: 184

Бренд: Weed Eater Страницы: 48

Бренд: Homelite Страницы: 36

Tri King 1900 Series

Бренд: Jacobsen Страницы: 30

Бренд: Woods Страницы: 28

Бренд: MTD Страницы: 35

Бренд: Garland Страницы: 120

Бренд: Peco Страницы: 12

Бренд: Mountfield Страницы: 50

Бренд: Eliet Страницы: 106

Бренд: Snapper Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды