Jacobsen Fairway 250 JGZZ250 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 99

background image

en-36

6 CONTROLS

6.2.D.

CHARGING WARNING LAMP ________________________________________

The red lamp illuminates when the ignition is turned on
and turns off when the engine starts.
If the light illuminates while the engine is in operation, the
fan belt has moved or is broken. The light can indicate a
fault in the electrical system. STOP THE VEHICLE
IMMEDIATELY.

6.2.E.

ENGINE OIL PRESSURE WARNING LAMP _____________________________

The red lamp illuminates when the ignition is turned on
and turns off when the engine starts.
If the light illuminates while the engine is in operation,
the engine oil pressure has fallen to a level that is not
safe. STOP THE VEHICLE IMMEDIATELY. Check the
level of oil in the sump and fill to a safe level. Check the
oil-pressure sender switch. Continued operation with the
light illuminated can cause damage to the engine.

6.2.F.

FUEL GAUGE _____________________________________________________

The fuel gauge is found to the left of the engine
temperature gauge. The fuel gauge indicates the
quantity of fuel in the vehicle.

FUEL

E

F

«
...
35
36
37
38
39
...
»

Содержание Fairway 250 JGZZ250




































































































Отзывы:

Нет отзывов

Похожие инструкции для Fairway 250 JGZZ250

Бренд: Toro Страницы: 2

Бренд: McConnel Страницы: 108

Бренд: Snapper Страницы: 40

Бренд: Yazoo/Kees Страницы: 19

ULTRAVAC BAGGER

Бренд: Exmark Страницы: 19

Бренд: Country Clipper Страницы: 28

LMO 18-36 Battery

Бренд: Kärcher Страницы: 252

Wheel Horse XL 380H

Бренд: Toro Страницы: 40

Бренд: P.I.T. Страницы: 23

Yanmar 59A40009727

Бренд: Cub Cadet Страницы: 24

Бренд: Gravely Страницы: 54

Бренд: Kärcher Страницы: 17

Бренд: Bushranger Страницы: 20

Бренд: Gardeo Страницы: 53

Бренд: Gardenline Страницы: 28

Бренд: GARDEO PRO Страницы: 99

Бренд: Gardena Страницы: 12

Бренд: Craftsman Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды