Jacobsen Fairway 250 JGZZ250 Скачать руководство пользователя страница 89

Страница: 89 / 99

en-86

12 QUALITY OF CUT

12.2

MARCELLING______________________________________________________

NOTE: Arrow indicates direction of travel.

Marcelling, like washboarding, is a repeated pattern

of different cutting heights, that causes an appear-
ance that is like a wave.

In most cases, the wave tip-to-tip distance is 2 inch-

es (5 cm).

Possible Cause

Solution

The cut (ground) speed is higher than normal.

Decrease the cut (ground) speed.

The height-of-cut setting is not high enough for the

turf conditions.

Make sure that the height of cut is adjusted to the

turf conditions.

Cutting reel diameter is worn.

Check the cutting reel diameter. When the reel is

worn, the reel must be replaced.

TN0220

Содержание Fairway 250 JGZZ250




































































































Результаты поиска

Содержание Fairway 250 JGZZ250

Отзывы:

Похожие инструкции для Fairway 250 JGZZ250

Бренды по названию

Популярные бренды

Jacobsen Fairway 250 JGZZ250, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Fairway 250 JGZZ250

Отзывы:

Похожие инструкции для Fairway 250 JGZZ250

Бренды по названию

Популярные бренды