Jacobsen Fairway 250 JGZZ250 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 99

background image

en-21

4 SPECIFICATIONS

4.5

NOISE ______________________________________________________________

When the machine was tested for sound pressure (Operator Ear).

The Machinery Safety Directive 2006/42/EC
And
Exposure Of Workers To The Risks Arising From Physical Agents (Noise) Directive 2003/10/EC

By compliance to:
The Lawnmower Standard BS EN ISO 5395:2013
And
Sound Pressure Standard EN ISO 3746: 2010

Fairway 250 with ROPS Measured Sound Pressure 87.4 dB(A) ± 0.86 LWA
Fairway 305 with ROPS Measured Sound Pressure 86 dB(A) ± 0.86 LWA
Fairway 405 with ROPS Measured Sound Pressure 86 dB(A) ± 0.86 LWA

Fairway 305 with Cab Measured Sound Pressure 89 dB(A) ± 0.86 LWA
Fairway 405 with Cab Measured Sound Pressure 92 dB(A) ± 0.86 LWA

When the machine was tested for sound power (Noise in the Environment).

The Machinery Safety Directive 2006/42/EC
And
Noise Emission In The Environment By Equipment For Use Outdoors
Directive 2000/14/EC

By compliance to:
Sound Power Standard EN ISO 3744:2010

Fairway 250 Measured Sound Power 104 dB(A) ± 0.86 LWA
Fairway 305 Measured Sound Power 103 dB(A) ± 0.86 LWA
Fairway 405 Measured Sound Power 103 dB(A) ± 0.86 LWA

4.6

SLOPES ____________________________________________________________

DO NOT USE ON SLOPES GREATER THAN 20°. This slope was calculated using static stability measurements
according to the requirements of BS EN ISO 5395

«
...
20
21
22
23
24
...
»

Содержание Fairway 250 JGZZ250




































































































Отзывы:

Нет отзывов

Похожие инструкции для Fairway 250 JGZZ250

Бренд: Gardena Страницы: 56

Бренд: Gardena Страницы: 4

Бренд: Gardenline Страницы: 20

Бренд: Flymo Страницы: 11

Бренд: McCulloch Страницы: 44

Sweep It 23630YW

Бренд: Yardwise Страницы: 8

Бренд: Yardworks Страницы: 27

Бренд: Jacobsen Страницы: 50

Бренд: Challenge Страницы: 19

Бренд: Toro Страницы: 2

Бренд: Snapper Страницы: 52

Бренд: IDS Страницы: 34

Бренд: Alamo Страницы: 110

Parklander 2690997

Бренд: Murray Страницы: 36

Бренд: RHINO Страницы: 160

Бренд: Baroness Страницы: 40

Бренд: Craftsman Страницы: 68

Бренд: Craftsman Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды