Jacobsen Fairway 250 JGZZ250 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 99

background image

en-77

9 ADJUSTMENTS

9.10

SEAT (GRAMMER MSG85) ____________________________________________

The seat can be adjusted for operator's weight and leg reach to provide a comfortable position for
operating the machine.

1.

ADJUSTMENT FOR OPERATOR WEIGHT

To Adjust:
Rotate knob (A) to the right to increase the operator
weight setting. Turn to the left to decrease the
operator weight The set weight is indicated on the
yellow face dial next to the lever. Set at the correct
weight of the operator before operation. Failure to do
so will compromise the machine safety devices.

2.

FORE AND AFT ADJUSTMENT

To Adjust:
The position of the adjusting lever is on the right hand
side of the seat below the seat cushion (B). By moving
the lever towards the seat, the seat can be slid
backwards and forwards. When in the desired position
release the lever to locate in one of the pre-set
positions.

3.

BACK REST ADJUSTMENT

The back rest has three preset positions

To Adjust:
The position of the release lever is on the left hand
side of the seat back rest (C). Move the lever upwards
to move the upper part of the back rest forward. Move
the lever downwards to move the upper part of the back
rest rearwards.

NOTE:The seat is fitted with a micro-switch to sense operator presence. When the machine is fitted with a ROPS
frame or cab a lap belt is fitted and should be worn at all times.

WARNING

The Operator Weight must be set to the actual weight of the Operator. Safety Systems will be

compromised if this is not done.

«
...
77
78
79
80
81
...
»

Содержание Fairway 250 JGZZ250




































































































Отзывы:

Нет отзывов

Похожие инструкции для Fairway 250 JGZZ250

Бренд: Jacobsen Страницы: 58

Бренд: Jacobsen Страницы: 106

Бренд: Jacobsen Страницы: 60

Бренд: Jacobsen Страницы: 58

Бренд: Jacobsen Страницы: 118

Бренд: Jacobsen Страницы: 160

Бренд: Jacobsen Страницы: 20

Бренд: Jacobsen Страницы: 30

Greens King IV Plus

Бренд: Jacobsen Страницы: 60

Greens King IV Plus

Бренд: Jacobsen Страницы: 32

Ransomes HR 6010

Бренд: Jacobsen Страницы: 76

Бренд: Jacobsen Страницы: 48

Бренд: P.Lindberg Страницы: 47

Бренд: Toro Страницы: 52

Бренд: Brute Страницы: 44

67971 - LF 3400

Бренд: Jacobsen Страницы: 122

Бренд: Wards Garden Mark Страницы: 16

Бренд: Exmark Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды