Jacobsen Fairway 250 JGZZ250 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 99

background image

en-2

INTRODUCTION 2

2.1

IMPORTANT__________________________________________________________

The Ransomes FAIRWAY 250.305 and 405 are Diesel engined self propelled Reel mowers. The hydraulic
systems are for the traction drive, the cutting unit lift and the lower and cutting unit drives and steering.

IMPORTANT: Do the maintenance indicated in this manual to make sure that the quality of cut is kept at a high
level.

This SAFETY AND OPERATORS MANUAL is part of the machine and must stay with the machine always.
Suppliers of both original and used machines need to keep the documentation that comes with the machine.

You must use the machine to cut the grass only and not for any other purpose. Compliance with the conditions of
operation, service and repair specified by the manufacturer, are understood to be part of the correct use.

ALL operators MUST read through this manual and understand the Safety Instructions, controls, lubrication and
maintenance procedures.

Make sure that you obey all safety and road traffic regulations.

You must not make any changes to the machine that the manufacturer does not approve. This type of change
can release the manufacturer from the liability for any damage or injury.

Discard worn parts, taking note of the environmental result, use the systems available in the country where the
machine is used. When the machine is at its end of life, there are guidelines in this manual for the removal of the
machine from use.

Use only Ransomes Jacobsen Genuine spare parts to make sure that European conformity is controlled.

2006/42/EC
These instructions are the Original instructions confirmed by Ransomes Jacobsen Limited

«
1
2
3
4
5
...
»

Содержание Fairway 250 JGZZ250




































































































Отзывы:

Нет отзывов

Похожие инструкции для Fairway 250 JGZZ250

Бренд: Gardeline Страницы: 19

Gold 500 Series

Бренд: MTD Страницы: 32

Бренд: Poulan Pro Страницы: 56

Бренд: Worx Страницы: 24

Бренд: Cub Cadet Страницы: 39

Бренд: Zoef Robot Страницы: 54

Бренд: Improvements Страницы: 5

Бренд: AEG Страницы: 36

Бренд: Ikra Страницы: 56

Бренд: Husqvarna Страницы: 11

Бренд: Husqvarna Страницы: 24

Бренд: Husqvarna Страницы: 24

Бренд: Husqvarna Страницы: 40

PZ5426FX / 966614001

Бренд: Husqvarna Страницы: 34

Бренд: Husqvarna Страницы: 10

Бренд: Husqvarna Страницы: 48

McCULLOCH M53-190ER

Бренд: Husqvarna Страницы: 28

Бренд: Husqvarna Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды