Jacobsen Fairway 250 JGZZ250 Скачать руководство пользователя страница 14

Страница: 14 / 99

en-13

3 SAFETY

WARNING

California Proposition 65

Engine Exhaust, Some Of Its Constituents, And Some Vehicle Components Contain Or Release Chemicals

Known To The State Of California To Cause Cancer And Birth Defects Or Other Reproductive Harm.

WARNING

To Prevent Injury From The Hot Oil At High Pressure, Do Not Use Your Hands To Check For Oil Leaks. Make

Sure That You Use Paper Or Cardboard.

Release Of Hydraulic Fluid At High Pressure Has Enough Force To Enter Through The Skin. If The Fluid Enters

Through The Skin, The Fluid Must Be Surgically Removed Within Hours By A Specialist Doctor Or Gangrene

May Result.

WARNING

When The Machine Is Driven Off-Road, A Seat Belt Must Be Worn Only When A Rops Frame Is In Position.

This Warning Is Because A Seat Belt Must Be Worn With A Rops To Follow The Machinery Directive,

2006/42/EC Sections 3.2.2, Seating & 3.4.3, Rollover. (ANSI B71.4-2012 section 20.7)

Ransomes Jacobsen Limited Recommends That The Owner/User Of The Machine Completes A Local Risk

Assessment Of The Machine To Find Any Conditions That Do Not Follow This Rule. E.g. When You Drive The

Machine Next To Water Or On The Highway.

WARNING

Explosive Gases Are Released By Batteries. The Battery Contains Corrosive Acid And Supply An Electrical

Current That Is High Enough To Cause Burn Injuries To The Body.

WARNING

You Must Not Use This Machine To Tow Other Vehicles.

WARNING

Ear Protection Must Be Worn When You Operate Machines With

An Operator Ear Noise Level Of More Than 85 db(A) Leq.

Содержание Fairway 250 JGZZ250




































































































Результаты поиска

Содержание Fairway 250 JGZZ250

Отзывы:

Похожие инструкции для Fairway 250 JGZZ250

Бренды по названию

Популярные бренды

Jacobsen Fairway 250 JGZZ250, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Fairway 250 JGZZ250

Отзывы:

Похожие инструкции для Fairway 250 JGZZ250

Бренды по названию

Популярные бренды