Jacobsen Fairway 250 JGZZ250 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 99

background image

en-12

SAFETY 3

3.1.8

Important Safety Notes

This safety alert symbol is used to alert you to possible hazards.

DANGER:
Indicates a dangerous condition that WILL cause death or injury unless it is prevented.

WARNING:
Indicates a dangerous condition that CAN cause death or injury unless it is prevented.

CAUTION:
Indicates a dangerous condition that can cause injury and property damage unless it is prevented. Also, the label

can indicate work procedures that are not safe.

IMPORTANT:

Only drive the machine at road speed when you are on a highway. You must not select road speed on grass

areas or rough roads and gravel tracks.

Some illustrations in this manual can show shields, guards or plates removed for clearness. This equipment must
not be operated without these devices correctly fastened in position.

By following all instructions in this manual, you increase the life of your machine and keep its maximum
performance. Adjustments and maintenance must always be done by an approved technician.

If additional information or service is needed. Contact your Authorized Ransomes Jacobsen Dealer, who knows
the latest methods to service this equipment and can give that service.

WARNING

The Interlock System on this mower prevents the starting of the mower unless a.) The parking brake is
Engaged. b.) The mow switch is in the OFF position, c.) The traction pedal is in the Neutral position. d) The
operator is in the seat. The system stops the engine when the operator leaves the seat a.) without the parking
brake engaged or b.) the mow switch is not in the OFF position. NEVER operate the mower unless the
Interlock System is working.

WARNING

1.

Before leaving the operator’s position for any reason:

a.

Return traction pedal to the Neutral position.

b.

Disengage all drives.

c.

Lower all implements to the ground.

d.

Engage parking brake.

e.

Stop the engine and remove the ignition key.

2.

Keep your hands, feet, and clothing away from moving parts. Wait for all movement to stop before you
clean, adjust, or service the machine.

3.

Keep the area of operation clear of all persons and animals.

4.

Never carry any passengers.

5.

Never operate the equipment without a correctly fastened grass deflector in position.

«
...
11
12
13
14
15
...
»

Содержание Fairway 250 JGZZ250




































































































Отзывы:

Нет отзывов

Похожие инструкции для Fairway 250 JGZZ250

44 968999551, 50 968999552, 44

Бренд: Dixon Страницы: 88

Hayterette 005E

Бренд: Hayter Страницы: 36

Agco Allis 1692173

Бренд: Simplicity Страницы: 60

Бренд: Yard-Man Страницы: 12

Бренд: Yard force Страницы: 49

Бренд: Worx Страницы: 64

Бренд: Murray Страницы: 52

Бренд: Cub Cadet Страницы: 20

Бренд: Racing Страницы: 20

Timing Deck Striper/Roller

Бренд: Cub Cadet Страницы: 8

TOURNO compact 115

Бренд: Cramer Страницы: 26

Бренд: Snapper Страницы: 15

Бренд: Snapper Страницы: 24

Бренд: Snapper Страницы: 12

Бренд: Snapper Страницы: 52

Бренд: Snapper Страницы: 54

LT115D331B Series

Бренд: Snapper Страницы: 16

LT180H331BV series I

Бренд: Snapper Страницы: 176

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды