Jacobsen Fairway 250 JGZZ250 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 99

background image

en-53

7

OPERATION

7.12.2 TRANSPORTING ON A TRAILER OR FLATBED ___________________________

The Machine Has Hard-point Tie-down Loops Front (A) And Rear (B). Fasten The Mower To The Transport
Vehicle.

The machine has hard-point tie-down loops front (A) and rear (B). Fasten the mower to the transport vehicle.

Make sure that all tie down straps are tight. Make sure that the decks are locked in the transport position. Check
the fuel and hydraulic tank caps are tight. Make sure that no part of the mower can fall during transport.

Always follow the given maximum transport load weight for the vehicle used.

Do Not carry more than the maximum weight shown on the transport vehicle plate.

Read the Safety and Operation manual of the transport vehicle before you load.

Slinging
When Slinging The Mower, Damage Free Clamps Must Be Used, See The
Illustration, With An Approved Lift Frame. Information Is Available At
Www.tipnlift.co.uk.

Jacking
The Machine Jack Points Indicated By The Decal Shown.two For Each Axle On
Four Wheel Vehicles. Other Axle Types Are Different, Check The Safety And
Operations Manual For The Safe Jack Points.

A

B

«
...
52
53
54
55
56
...
»

Содержание Fairway 250 JGZZ250




































































































Отзывы:

Нет отзывов

Похожие инструкции для Fairway 250 JGZZ250

Бренд: MTD Страницы: 6

Бренд: Qualcast Страницы: 24

18.5HP Z-Force 42

Бренд: Cub Cadet Страницы: 56

HydroCut 5900604

Бренд: Ferris Страницы: 54

Бренд: Viking Страницы: 284

Бренд: Bolens Страницы: 32

Бренд: Toro Страницы: 28

Бренд: Improvements Страницы: 5

Бренд: dormak Страницы: 24

Бренд: Craftsman Страницы: 8

Бренд: Husqvarna Страницы: 8

Бренд: Husqvarna Страницы: 88

Бренд: Husqvarna Страницы: 88

Бренд: Husqvarna Страницы: 112

AUTOMOWER 260 ACX

Бренд: Husqvarna Страницы: 72

Бренд: Husqvarna Страницы: 76

Бренд: Husqvarna Страницы: 36

Бренд: Husqvarna Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды