Jacobsen Fairway 250 JGZZ250 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 99

background image

en-38

6 CONTROLS

6.2.K

CUTTING UNIT SWITCHES ________________________________________

When you cut, make sure that the speed limiter is set to
the mow position. Press the bottom of the rocker switch
(G) to activate the joystick. Lower the cut reels and press
the foot switch (A) to start the cut reel rotation. Push the
top of rocker switch to stop the cut reel rotation and
deactivate the joystick. When the cut units are lifted, the
rotation of the reels automatically stops.

6.2.L

PARKING BRAKE SWITCH SERIES JN, KD, JU, KE ____________________

When the engine is running the Parking brake is applied by
depressing the switch. The Parking Brake is applied
automatically when the engine is stopped.

If the operator leaves the seat for 5 seconds the cutting units will
stop and if the transmission pedal is operated the engine will
stop.

To release the parking brake slide the orange button and
depress the rocker switch.

G

«
...
37
38
39
40
41
...
»

Содержание Fairway 250 JGZZ250




































































































Отзывы:

Нет отзывов

Похожие инструкции для Fairway 250 JGZZ250

Бренд: Walker Страницы: 100

Бренд: Sabo Страницы: 244

Wheel Horse 265-6

Бренд: Toro Страницы: 44

Бренд: Jacobsen Страницы: 148

Бренд: Solo Страницы: 88

69168 - Turfcat T628D

Бренд: Jacobsen Страницы: 59

Бренд: Stiga Страницы: 294

Бренд: Garland Страницы: 160

Бренд: Powersmart Страницы: 73

Бренд: Garten Meister Страницы: 84

Бренд: Dolmar Страницы: 224

Бренд: Gardeo Страницы: 128

Бренд: Cub Cadet Страницы: 20

Бренд: Deutz-Allis Страницы: 36

Бренд: Einhell Royal Страницы: 24

Recycler 119-3320

Бренд: Toro Страницы: 4

Бренд: TYM Страницы: 169

Бренд: Cub Cadet Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды