Jacobsen Fairway 250 JGZZ250 Скачать руководство пользователя страница 81

Страница: 81 / 99

en-79

9 ADJUSTMENTS

9.11.3 BACKREST EXTENSION * ** _________________________________________

To adjust the backrest extension for each driver,
move the extension to the correct lock position.

To remove the backrest extension, move the
extension over the end stop.

* If

Installed

** Optional

Accessory

9.11.4 SEAT HEATER * ** _________________________________________________

Press the seat heater switch to turn the seat heater
on and to turn off.

0 = seat heater ‘OFF’
I = seat heater ‘ON’

* If

Installed

** Optional

Accessory

9.11.5 LUMBAR SUPPORT_________________________________________________

The lumbar support improves the quality of the seat
and increases the performance of the driver.

To adjust the curve in the upper part of the backrest
cushion, rotate the adjustment knob to the top.
To adjust the curve in the lower part of the backrest
cushion, rotate the adjustment knob to the bottom.

0 = No curve angle
1 = Maximum curve angle at the top
2 = Maximum curve angle at the bottom

Содержание Fairway 250 JGZZ250




































































































Результаты поиска

Содержание Fairway 250 JGZZ250

Отзывы:

Похожие инструкции для Fairway 250 JGZZ250

Бренды по названию

Популярные бренды

Jacobsen Fairway 250 JGZZ250, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Fairway 250 JGZZ250

Отзывы:

Похожие инструкции для Fairway 250 JGZZ250

Бренды по названию

Популярные бренды