Jacobsen Fairway 250 JGZZ250 Скачать руководство пользователя страница 86

Страница: 86 / 99

en-84

11 PROBLEM SOLVING

11.1 PROBLEM SOLVING GENERAL ______________________________________________________

Problems

Possible Causes

Action

Engine will not start

The glow plug has not turned off.

Set the ignition switch again and allow the glow plug to turn off
before you turn the engine.

Battery low on charge or has
defects.

Inspect the condition of battery and battery connections.

The fuel tank empty or fuel is
dirty.

Fill the tank with clean fuel. Change the filter, Bleed air from
the lines.

Blown fuse.

Replace the Fuse.

The starter relay has defects.

Test the relay. If a replacement is needed, replace the relay.

The mow switch set to cut.

Set the mow switch to the OFF position.

Transport pedal not in neutral
position.

Remove foot from the pedal and make sure that the pedal
returns to the neutral position.

Engine is difficult to

start or does not run

correctly.

The fuel tank empty or fuel is
dirty.

Fill the tank with clean fuel. Change the filter, Bleed air from
the lines.

Air Cleaner has a blockage or
dirty.

Check air cleaner, replace as necessary.

Injectors, fuel pump.

Refer to the engine manual.

Содержание Fairway 250 JGZZ250




































































































Результаты поиска

Содержание Fairway 250 JGZZ250

Отзывы:

Похожие инструкции для Fairway 250 JGZZ250

Бренды по названию

Популярные бренды

Jacobsen Fairway 250 JGZZ250, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Fairway 250 JGZZ250

Отзывы:

Похожие инструкции для Fairway 250 JGZZ250

Бренды по названию

Популярные бренды