jablotron JA-101K Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 110

jablotron JA-101K Скачать руководство пользователя страница 53

JABLOTRON

ALARMS

a.s.

Pod

Skalkou

4567/33

46601

Jablonec

n.

Nisou

Czech

Republic

www

.jablotron.com

||

|

JA-101K(-LAN)(-LAN3G) and JA-106K(-3G)
Security System Control Panels

53

/

110

MLJ51410

9.13 Overview table of Groups of Events reported to users

All events which are sent to users (35) are assigned to 5 basic groups. Every single group can be assigned to

users arbitrary. Users to whom a group will be assigned will be sent reports from this group. When the basic
settings of the groups are not enough then there are two special groups which can be used. User defined group
1 and 2. Events can be added to those groups and can be given to only specific users.

Overview table:

Order

Event

Group

1

Setting

SMS about Setting / Unsetting (3)

2

Unsetting

SMS about Setting / Unsetting (3)

3

Partially setting

SMS about Setting / Unsetting (3)

4

30 minute mains fault

SMS alerts (1) / Alarm call (2)

5

Mains restored after 30 min

SMS alerts (1) / Alarm call (2)

6

Instant alarm

SMS alerts (1) / Alarm call (2)

7

Instant alarm cancelled

SMS alerts (1) / Alarm call (2)

8

Delay alarm

SMS alerts (1) / Alarm call (2)

9

Delay alarm cancelled

SMS alerts (1) / Alarm call (2)

10

Tamper alarm

SMS alerts (1) / Alarm call (2)

11

Tamper alarm cancelled

SMS alerts (1) / Alarm call (2)

12

Fire alarm

SMS alerts (1) / Alarm call (2)

13

Fire alarm cancelled

SMS alerts (1) / Alarm call (2)

14

Panic alarm

SMS alerts (1) / Alarm call (2)

15

Panic alarm cancelled

SMS alerts (1) / Alarm call (2)

16

Health troubles

SMS alerts (1) / Alarm call (2)

17

Flooding

SMS alerts (1) / Alarm call (2)

18

Code breaking attempt

SMS alerts (1) / Alarm call (2)

19

Set with active zone (when confirmation enabled)

SMS alerts (1) / Alarm call (2)

20

Section without movement

SMS alerts (1) / Alarm call (2)

21

System start (out of service mode)

Fault and service SMS (5)

22

Device low battery

Fault and service SMS (5)

23

Device battery OK

Fault and service SMS (5)

24

Fault (device, communicator)

Fault and service SMS (5)

25

Fault end

Fault and service SMS (5)

26

Service mode entry

Fault and service SMS (5)

27

Service mode left

Fault and service SMS (5)

28

Low BATTERY

Fault and service SMS (5)

29

BATTERY OK

Fault and service SMS (5)

30

ARC communication fault

Fault and service SMS (5)

31

ARC communication restored

Fault and service SMS (5)

32

RF jamming

Fault and service SMS (5)

33

RF jamming end

Fault and service SMS (5)

34

Low credit balance

Fault and service SMS (5)

35

Alarm photo

Photo (4)

The assignment of events distinguished by the system to groups is specified in the table. On occurrence of an

event the system generates an SMS in the format:

Installation name

(see the Initial setup tab):

Time

(of event occurrence),

Event

(see table).

Event source

(see the Device/Name or User/Name tab),

Section

(where the event occurred); (in case of

more events they are arranged one after another in one message separated with semicolons);

Time

(time and date of sending)

Example of a sent SMS:

JABLOTRON 100

(installation name)

17:01:10, Delayed alarm

(event time, event)

Door magnet, Ground floor

(detector name, section name)

17:01:25, Instant alarm

(event time, event)

Staircase movement, Upstairs

(detector name, section name)

Time 17:01 22.7.

(time of sending)

«
...
51
52
53
54
55
...
»

Содержание JA-101K















































































































Отзывы:

Нет отзывов