Invacare TDX-SP N Скачать руководство пользователя | Manualshive

Страница: 69 / 88

background image

SECTION 9—BATTERIES

Part No 1143209

69

Removing the Batteries from Wheelchair

WARNING

Risk of Serious Injury
Improperly installed battery tray can cause instability resulting in serious injury.
- Ensure batteries and battery tray are installed properly to maintain stability.

NOTE: For this procedure, refer to FIGURE 9.3.

1.

Slide battery tray with batteries out.

2.

Disconnect the battery straps.

3.

Unplug front battery from rear battery.

4.

Remove the front battery.

5.

Slide the rear battery forward and remove it from the tray.

FIGURE 9.3

Removing the Batteries from Wheelchair

Installing Batteries into Wheelchair

NOTE: For this procedure, refer to FIGURE 9.3 and FIGURE 9.4 on page 70.

NOTE: Positioning of the batteries into the battery tray is completed with battery tray positioned in wheelchair and partially pulled out.
Refer to FIGURE 9.3 for full view of wheelchair base. Illustrations in FIGURE 9.4 on page 70 are shown without the wheelchair for
clarification purposes only.

1.

Position the battery with battery connector bracket in the rear of the battery tray in the orientation as shown. See Detail
“A” of FIGURE 9.4 on page 70.

NOTE: Front of battery tray is designated by the battery stop. Rear of the battery tray is the opposite end.

NOTE: Orientation of the battery is critical otherwise batteries will not connect to the controller or each other.

2.

Position the remaining battery in the front of the battery tray in the orientation shown so that the wiring harnesses can
be connected together. See Detail “B” of FIGURE 9.4 on page 70.

3.

Connect front battery to rear battery. See Detail “B” of FIGURE 9.4 on page 70.

4.

Connect battery straps. See Detail “C” of FIGURE 9.4 on page 70.

5.

Slide the battery tray into the wheelchair (FIGURE 9.3).

6.

Install the battery door and rear shroud. Refer to Installing the Front Shroud/Battery Retention Bracket and Rear Shroud
on page 70.

Disconnect Front Battery

from Rear Battery Here

FRONT OF

WHEELCHAIR

Rear Battery

Front Battery

Battery Straps

NOTE: Battery tray shown
removed for clarity.

Battery Tray

NOTE: 22NF Batteries
shown.

«
...
67
68
69
70
71
...
»

Содержание TDX-SP N

























































































Отзывы:

Нет отзывов

Похожие инструкции для TDX-SP N

MOPEDIA RC220-43

Бренд: Moretti Страницы: 20

iChair DYNAMIC 1.623

Бренд: Meyra Страницы: 48

Бренд: Z-Tec Страницы: 4

Бренд: I-GO Страницы: 28

Бренд: Handicare Страницы: 99

Бренд: E&J Страницы: 20

NXT Generation NEXT

Бренд: Invacare Страницы: 43

Adventure Control

Бренд: Carpe Iter Страницы: 10

Бренд: Invacare Страницы: 144

Бренд: Yamaha Страницы: 46

Бренд: Quantum Rehab Страницы: 2

Бренд: Medicare Technology Страницы: 22

Бренд: chinesport Страницы: 8

Бренд: chinesport Страницы: 10

M2 Flexi-Tip 310216

Бренд: HMN Страницы: 16

Бренд: Rehab Страницы: 26

Бренд: B+B Страницы: 62

SM-100.5 Series

Бренд: SOMA Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды