Invacare TDX-SP N Скачать руководство пользователя

Страница: 47 / 88

SECTION 6—SIDE FRAME

Part No 1143209

TDX® SP

Removing/Installing the Fender Assembly

NOTE: For this procedure, refer to FIGURE 6.5.

Removing

Remove the drive wheel. Refer to Removing/Installing the SSD Motor Drive Wheel/Wheel Hub on page 34.

Remove the three 10-32 X 5/8-inch hex head screws that secure the fender to the swingarm.

Remove fender from the walking beam.

Installing

Align the fender with the walking beam.

Secure the fender to the fender bracket with the three 10-32 X 5/8-inch mounting screws. Securely tighten. Torque to 40
in-lbs.

Install the drive wheel. Refer to Removing/Installing the SSD Motor Drive Wheel/Wheel Hub on page 34.

FIGURE 6.5

Removing/Installing the Fender Assembly from a 2-Pole and 4-Pole Motor

Removing/Installing the Front Bumpers

NOTE: For this procedure, refer to FIGURE 6.6.

NOTE: If replacing one or more bumpers, it is recommended to replace all four bumpers.

NOTE: This procedure applies to forward and rear facing bumpers on both sides of the wheelchair.

NOTE: Reverse this procedure to install the bumper.

Bolt-On Front Bumpers

Remove the drive wheel. Refer to Removing/Installing
the SSD Motor Drive Wheel/Wheel Hub on page 34.

Remove the 5/16-18 keps nut and .328 X .75 X .060
washer securing the front bumper to the wheelchair
frame.

Remove the bumper from wheelchair frame.

If necessary repeat STEPS 1-3 on remaining bumpers.

FIGURE 6.6

Removing/Installing the Front Bumpers

Walking Beam

Fender

10-32 X 5/8-inch Hex

Head Screw

Front Bumper

5/16-18 Keps Nut

.328 X. 75 X .060 Washer

Содержание TDX-SP N

























































































Результаты поиска

Содержание TDX-SP N

Отзывы:

Похожие инструкции для TDX-SP N

Бренды по названию

Популярные бренды

Invacare TDX-SP N, Руководство по обслуживанию

Результаты поиска

Содержание TDX-SP N

Отзывы:

Похожие инструкции для TDX-SP N

Бренды по названию

Популярные бренды