Invacare TDX-SP N Скачать руководство пользователя

Страница: 34 / 88

SECTION 4—WHEELS AND WHEEL LOCKS

TDX® SP

Part No 1143209

SECTION 4—WHEELS AND WHEEL LOCKS

NOTE: The following tools and materials are required to perform this procedure:

•

13-mm socket with ratchet

•

Needle-nose pliers

•

Wheel puller

•

Two 5-inch blocks

•

Torque wrench

•

Loctite 242

•

Anti-sieze compound

Removing/Installing the SSD Motor Drive Wheel/Wheel Hub

NOTE: For this procedure, refer to FIGURE 4.1

NOTE: Reverse this procedure to install the drive wheels.

Place two 5-inch blocks under battery frame to lift frame off the ground for ease in performing this procedure.

Remove the five mounting screws securing the drive wheel to the wheel hub.

Remove the drive wheel from the wheel hub.

If necessary, remove the locknut, washer, wave washer and 5mm spacer securing the wheel hub on the drive shaft.

If necessary, repeat STEPS 2-3 to remove the remaining drive wheel.

FIGURE 4.1

Removing/Installing the SSD Motor Drive Wheel/Wheel Hub

Removing/Installing the Inside Rim and Pneumatic Tire

NOTE: For this procedure, refer to FIGURE 4.2.

Removing

Remove the drive wheel. Refer to Removing/Installing the SSD Motor Drive Wheel/Wheel Hub on page 34.

DANGER

If wheelchair is equipped with pneumatic tires, deflate the tire before removing rim. Otherwise,

the rim and hardware will become projectiles and cause serious personal injury and/or damage

to surrounding property.

Remove the five 5/16-18 x 7/8-inch hex head cap screws that secure the inside rim to the outside rim.

Remove the inside rim and tire.

Installing

Place the outside rim against one side of the tire.

Place the inside rim against the other side of the tire.

NOTE: Align the mounting holes in the inside rim with the mounting holes in the outside rim.

Mounting Screws

Drive Wheel

Wheel Hub

Locknut

Washer

3mm Hub Spacer

Motor/Gearbox Assembly

Drive Shaft

Wave Washer

5mm Hub Spacer

Содержание TDX-SP N

























































































Результаты поиска

Содержание TDX-SP N

Отзывы:

Похожие инструкции для TDX-SP N

Бренды по названию

Популярные бренды

Invacare TDX-SP N, Руководство по обслуживанию

Результаты поиска

Содержание TDX-SP N

Отзывы:

Похожие инструкции для TDX-SP N

Бренды по названию

Популярные бренды