Invacare TDX-SP N Скачать руководство пользователя

Страница: 84 / 88

SECTION 11—TRANSPORT IN VEHICLES

TDX® SP

Part No 1143209

Vehicle-Anchored Belts

NOTE: For this procedure, refer to FIGURE 11.3.

With regard to accommodating the use and fit of vehicle-anchored belts, this wheelchair has an overall rating of:
•

TDX SP Adult - A

•

TDX SP Junior - B

This rating is scored as follows:

The test for Lateral Stability Displacement for Point (P) is shown in FIGURE 11.3. The average test result for point (P) is:

•

TDX SP Adult - 0.53-inches (13.4 mm)

•

TDX SP Junior - 0.57 inches (14.4 mm)

FIGURE 11.3

Vehicle-Anchored Belts

Seating System

This wheelchair has been tested for seating in a motor vehicle with the factory installed seating system ONLY.
Ensure that the factory installed seating system is secured to the wheelchair frame before operation. Refer to the seating

system user manual.

RATING

DESCRIPTION

Excellent

Good

Fair

Poor

Point (P)

Test Platform

45°

NOTE: Rear view of the wheelchair and human surrogate secured on test
platform and tilted to 45°.

Содержание TDX-SP N

























































































Результаты поиска

Содержание TDX-SP N

Отзывы:

Похожие инструкции для TDX-SP N

Бренды по названию

Популярные бренды

Invacare TDX-SP N, Руководство по обслуживанию

Результаты поиска

Содержание TDX-SP N

Отзывы:

Похожие инструкции для TDX-SP N

Бренды по названию

Популярные бренды