Invacare TDX-SP N Скачать руководство пользователя

Страница: 76 / 88

SECTION 10—ELECTRONICS

TDX® SP

Part No 1143209

FIGURE 10.3

Preparing MK6i Joystick For Use

Removing/Installing/Repositioning MK6i Joystick

NOTE: For this procedure, refer to FIGURE 10.4 on page 76.

Turn the adjustment lock lever to release the joystick mounting tube from the mounting bracket.

Disconnect the joystick connector from the controller connector.

Cut the tie wraps that secure the joystick cable in place.

Remove the joystick from wheelchair.

If repositioning joystick, perform the following:

A. Remove the three hex screws and washers that secure both halves of the mounting bracket to the arm tube.
B. Reposition the mounting bracket on the opposite arm tube, ensuring the threaded plate of the mounting bracket is on the

inside of the arm tube as shown.

C. Using the three hex mounting screws and washers, secure both halves of the mounting bracket to the arm tube.

NOTE: If replacing the exact same joystick then proceed to STEP 6. If installing a different joystick, call Technical Services for assistance.

Slide the new or existing joystick mounting tube through the mounting bracket to the desired position.

Turn the adjustment lock lever to secure the joystick mounting tube into the mounting bracket.

Connect the joystick connector to the controller connector.

Secure joystick cable in place with new tie wraps.

FIGURE 10.4

Removing/Installing/Repositioning MK6i Joystick

Mounting Bracket

Joystick Mounting

Tube

Adjustment Lock

Lever

NOTE: Joystick not shown

Washer

NOTE: Joystick not shown.

Hex Mounting

Screw

Adjustment Lock

Lever

Mounting

Bracket

Joystick Mounting Tube

Arm Tube

Mounting Bracket (Threaded Plate)

Содержание TDX-SP N

























































































Результаты поиска

Содержание TDX-SP N

Отзывы:

Похожие инструкции для TDX-SP N

Бренды по названию

Популярные бренды

Invacare TDX-SP N, Руководство по обслуживанию

Результаты поиска

Содержание TDX-SP N

Отзывы:

Похожие инструкции для TDX-SP N

Бренды по названию

Популярные бренды