Invacare TDX-SP N Скачать руководство пользователя

Страница: 75 / 88

SECTION 10—ELECTRONICS

Connect the joystick cable from the controller.

Connect the right and left motors form the controller.

Install the rear shroud. Refer to Adjusting the Formula CG Seating System Mounting Position on page 58.

Wheelchairs with TRRO, TRBKTS, or powered Seating System Installed ONLY: Using the four 5/16-18 X 5/8 socket head
cap screws, secure the pivot cross-member to the two rear swingarms (Detail “A”).

FIGURE 10.2

Removing/Installing the Controller

Preparing MK6i Joystick For Use

NOTE: For this procedure, refer to FIGURE 10.3.

Turn the adjustment lock lever to release the adjustment lock from joystick mounting tube (FIGURE 10.3).

Slide joystick mounting tube to the desired position.

Turn the adjustment lock lever to secure the adjustment lock to the joystick mounting tube.

Cables Connect Here

8-32 X .1.00-inch Phillips Pan

Head Tap Screws

Large Opening in the

Base Frame

9/16 ID X 1-1/16 OD X-3/8-inch Washer

Controller Mounting Washer

Controller

NOTE: Battery lead, joystick lead and
motor leads not shown.

8-32 Locknuts

Rear Swingarm

Pivot Cross-Member

5/16-18 X 5/8

Socket Head Cap

Screws

Rear Swingarm

DETAIL “A” - WHEELCHAIRS

WITH TRRO OR TTRBKTS

ONLY

Содержание TDX-SP N

























































































Результаты поиска

Содержание TDX-SP N

Отзывы:

Похожие инструкции для TDX-SP N

Бренды по названию

Популярные бренды

Invacare TDX-SP N, Руководство по обслуживанию

Результаты поиска

Содержание TDX-SP N

Отзывы:

Похожие инструкции для TDX-SP N

Бренды по названию

Популярные бренды