Invacare TDX-SP N Скачать руководство пользователя

Страница: 42 / 88

SECTION 6—SIDE FRAME

TDX® SP

Part No 1143209

SECTION 6—SIDE FRAME

Removing/Installing The Walking Beam Assembly

NOTE: For this procedure, refer to FIGURE 6.1 on page 43.

NOTE: Theses procedures apply to both sides of the wheelchair.

NOTE: It is recommended that an assistant be present when lifting the wheelchair frame.

Removing the Walking Beam Assembly

Remove batteries. Refer to Replacing Batteries on page 65.

Place two 5-inch blocks under battery frame to lift frame off the ground for ease in performing this procedure.

Remove the drive wheel. Refer to Removing/Installing the SSD Motor Drive Wheel/Wheel Hub on page 34.

Remove the lower pivot link. Refer to Removing/Installing the Lower Pivot Link on page 44.

Remove the upper and lower front bumpers. Refer to Removing/Installing the Front Bumpers on page 47.

Disconnect the 4-Pole motor connector from the controller.

NOTE: Take note of position and orientation of tie-wraps and wiring prior to removing tie-wraps.

Cut tie-wraps that secure the motor cable to the base frame.

Lift the rear suspension and depress the pivot ball pin to de-activate the locking mechanism of the locking-gas cylinder.

NOTE: Continue holding the rear suspention up to de-activate the locking-gas cylinder until the walking beam has been rotated into
position.

Rotate the walking beam assembly until the 5/16 X 2.50 socket head shoulder screw aligns with the circular opening in
the battery box.

10. Remove the 1/4-20 locknut securing the 5/16 X 2.50 socket head shoulder screw and the locking-gas cylinder to the

walking beam.

11. Push the 5/16 X 2.50 socket head shoulder screw towards the base frame and the locking-gas cylinder is free from the

walking beam assembly.

12. Position the locking-gas cylinder against the wheelchair frame.

13. Remove 1/2-20 locknut and.505 X 1.124 X .100 inch washer or washer plate securing the walking beam assembly to the

base frame.

NOTE: A coved washer is located between the walking beam assembly and the base frame.

14. Remove the walking beam assembly and coved spacer from the base frame.

Содержание TDX-SP N

























































































Результаты поиска

Содержание TDX-SP N

Отзывы:

Похожие инструкции для TDX-SP N

Бренды по названию

Популярные бренды

Invacare TDX-SP N, Руководство по обслуживанию

Результаты поиска

Содержание TDX-SP N

Отзывы:

Похожие инструкции для TDX-SP N

Бренды по названию

Популярные бренды