Invacare TDX-SP N Скачать руководство пользователя | Manualshive

Страница: 49 / 88

background image

SECTION 7—REAR FRAME

Part No 1143209

49

3.

Perform one of the following to compress the rear springs:

•

Block Method - Lift the rear frame assembly up and add spacers under the rear casters until the rear springs remains
compressed and the nylon spacer can be installed.

•

Clamp Method - Use a vise-clamp or c-clamp to compress springs until the nylon spacer can be installed.

4.

Using the two 1/4-20 X 5/8-inch mounting screws and nylon spacer, secure the rear frame assembly to the wheelchair
frame. Torque to 75 in-lbs ± 20%.

5.

Connect the right and left motor leads and the joystick cable to the controller.

NOTE: When Securing the wiring, ensure motor leeds have enough slack to allow full motion of the walking beam and that all wiring
will not become pinched or damaged by moving parts.

6.

Using tie-wraps, secure wiring and cables to rear frame.

7.

Remove the 5-inch blocks supporting the wheelchair frame.

8.

Install the two rubber end caps.

9.

Adjust the stability lock setting. Refer to Adjusting the Stability Lock Setting on page 53.

10. Install the rear shroud. Refer to Adjusting the Formula CG Seating System Mounting Position on page 58.

FIGURE 7.1

Removing/Installing the Rear Suspension Assembly

Rear Suspension

Assembly

Wheelchair Frame

1/2-13 X 1.0-inch

Mounting Screws

Rear Pivot

Bushings

1/4-20 X 5/8-inch

Mounting Screws

Nylon Spacer

Mounting Brackets

NOTE: Tie-wraps and wiring not shown.

Pivot Tube

Pivot Bar

Center Bushing Assembly

Rear Swingarms

Rear Pivot

Bushings

1/2-13 X 1.0-inch

Mounting Screws

Rear Pivot

Bushings

1/2-13 X 1.0-inch

Mounting Screws

NOTE: Rear suspension frame shown disassembled for clarity.

«
...
47
48
49
50
51
...
»

Содержание TDX-SP N

























































































Отзывы:

Нет отзывов

Похожие инструкции для TDX-SP N

Бренд: CareCo Страницы: 2

Бренд: CareCo Страницы: 16

Бренд: Drive Страницы: 36

Бренд: CareCo Страницы: 29

Comfort Company Inception

Бренд: Permobil Страницы: 4

Бренд: EZee Life Страницы: 6

Бренд: hugo Страницы: 8

Бренд: ubiolabs Страницы: 95

Бренд: Vermeiren Страницы: 30

Бренд: PG Drives Technology Страницы: 174

Бренд: panthera Страницы: 5

Бренд: panthera Страницы: 22

Бренд: panthera Страницы: 24

U3 Light Y-Front

Бренд: panthera Страницы: 24

Бренд: panthera Страницы: 25

Alante II GP202

Бренд: Golden Страницы: 40

Бренд: Sopur Страницы: 96

Xact Rehab Series

Бренд: Action Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды