Invacare TDX-SP N Скачать руководство пользователя | Manualshive

Страница: 60 / 88

background image

SECTION 8—BASE FRAME

60

Part No 1143209

Removing/Installing the Wheelchair Shrouds

NOTE: For this procedure, refer to FIGURE 8.5 on page 61.

NOTE: The following tools are required to perform this procedure.
•

Phillips Head Screwdriver

•

5/16-inch Allen Wrench

Top Shroud

NOTE: Reverse this procedure to install the top shroud.

1.

Remove the seat from the base frame.

2.

Remove the four 10-32 X 1/2-inch pan head screws securing the top shroud to the base frame.

3.

Lifting up, remove the top shroud from the base frame.

Rear shroud

NOTE: Reverse this procedure to install the rear shroud.

1.

Remove the three 10-32 X 1/2-inch pan head screws, thumb screw or lock knob securing the rear shroud to the base
frame.

2.

Remove the rear shroud from the base frame.

Front Shroud and Battery Retention Bracket

NOTE: Reverse this procedure to install the front shroud and battery retention bracket.
NOTE: The front shroud and battery retention bracket are removed from and installed onto the wheelchair frame as a single unit.

1.

Remove the two 5/16-18 X 5/8-inch socket head screws securing the front shroud/battery retention bracket to the base frame.

2.

Lift up to unhook the battery retention bracket from the base frame and remove the front shroud/battery retention
bracket from the base frame.

3.

If necessary to replace the front shroud or the battery retention bracket, perform the following:

A. Remove the four #8-16 X 5/8-inch Phillips screws securing the battery retention bracket to the front shroud.
B. Separate the front shroud from the battery retention bracket.
C. Discard the item to be replaced and replace with new front shroud or battery retention bracket.
D. Using four #8-16 X 5/8-inch Phillips screws, secure front shroud to the battery retention bracket.

«
...
58
59
60
61
62
...
»

Содержание TDX-SP N

























































































Отзывы:

Нет отзывов

Похожие инструкции для TDX-SP N

Бренд: Quickie Страницы: 44

Top End Terminator Everyday

Бренд: Invacare Страницы: 72

Бренд: Karisma Страницы: 20

Бренд: panthera Страницы: 7

Бренд: panthera Страницы: 12

Бренд: panthera Страницы: 20

Бренд: Levo AG Страницы: 41

Бренд: Glide Страницы: 13

Бренд: Vermeiren Страницы: 136

Бренд: A2J Страницы: 11

Бренд: Karman Healthcare Страницы: 30

Бренд: Karma Страницы: 48

Бренд: HD Rehab Страницы: 2

Junior Vector O2

Бренд: Vicair Страницы: 6

Бренд: Special mobility Страницы: 30

LIGHTNING PUSHCHAIR

Бренд: Stealth Страницы: 26

Бренд: Stealth Страницы: 52

Бренд: nxt Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды