Invacare TDX-SP N Скачать руководство пользователя | Manualshive

Страница: 62 / 88

background image

SECTION 9—BATTERIES

62

Part No 1143209

SECTION 9— BATTERIES

DANGER

Risk of Death or Serious Injury
Failure to observe these warnings can cause an electrical short resulting in death, serious injury,

or damage to the electrical system.
The POSITIVE (+) RED battery cable MUST connect to the POSITIVE (+) battery

terminal(s)/post(s).
The NEGATIVE (-) BLACK battery cable MUST connect to the NEGATIVE (-) battery

terminal(s)/post(s).
NEVER allow any of your tools and/or battery cable(s) to contact BOTH battery post(s) at the

same time. An electrical short may occur and serious injury or damage may occur.
Install protective caps on positive and negative battery terminals.
Replace cable(s) immediately if cable(s) insulation becomes damaged.
DO NOT remove fuse or mounting hardware from POSITIVE (+) red battery cable mounting

screw.

WARNING!

Risk of Injury or Damage
Improper installation of the battery can result in injury or damage.
– Batteries can weigh up to 52 lbs (23.6 kg). ALWAYS use a battery lifting strap when lifting the

battery. It is the most reliable method of carrying a battery and preventing serious injury.

WARNING!

Risk of Injury or Damage
Improper lifting technique may cause injury or damage.
– Use proper lifting techniques, assistance and gear such as straps when available when lifting

heavy loads.

WARNING!

Risk of Injury
Exposure to battery acid may result in injury.
– The use of rubber gloves is recommended when working with batteries.
– DO NOT allow the liquid in the battery to come in contact with skin, clothes or other

possessions. It is a form of acid and harmful or damaging burns may result. Should the liquid

touch your skin, wash the area IMMEDIATELY and thoroughly with cool water. In serious cases

or if eye contact is made, seek medical attention IMMEDIATELY.
– DO NOT install/reinstall a battery with a cracked or otherwise damaged case.

NOTE: Invacare strongly recommends battery installation and replacement be performed by a qualified technician. Read the installation
instructions noted on the battery and in the manual. Ensure there is no battery acid in the bottom or around the battery box or on the
sides of the battery(ies). Neutralize battery acid with baking soda if found. Clean battery tray and batteries prior to installation. Use
battery lifting strap when available. Keep batteries in an upright position and avoid tipping. Use only deep cycle gel cell battery. Use box
wrench when tightening clamps. Do Not wiggle the battery terminals/posts when tightening.

«
...
60
61
62
63
64
...
»

Содержание TDX-SP N

























































































Отзывы:

Нет отзывов

Похожие инструкции для TDX-SP N

Бренд: Q'STRAINT Страницы: 36

Бренд: PDG Mobility Страницы: 38

Бренд: Quickie Страницы: 8

Бренд: Decon wheel Страницы: 4

Бренд: Otto Bock Страницы: 36

Бренд: Timago Страницы: 7

Бренд: Timago Страницы: 7

Kanga 1300-921110

Бренд: Inspired by drive Страницы: 8

Expedition Plus

Бренд: Drive Страницы: 12

Бренд: Quantum Rehab Страницы: 47

Бренд: CareCo Страницы: 11

Бренд: Sunrise Medical Страницы: 44

Бренд: Harbor Freight Tools Страницы: 8

Бренд: Permobil Страницы: 33

ROHO QUADTRO SELECT Series

Бренд: Permobil Страницы: 2

Бренд: Permobil Страницы: 206

Бренд: HealthSmart Страницы: 2

Easy STD 56-272Easy STD 56-273

Бренд: Gate Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды