Invacare TDX-SP N Скачать руководство пользователя | Manualshive

Страница: 55 / 88

background image

SECTION 8—BASE FRAME

Part No 1143209

55

SECTION 8—BASE FRAME

Removing/Installing Seat

NOTE: Before removing the seat assembly, note the position and orientation of the mounting position and hardware.
NOTE: If making any changes to the seat assembly that would effect the wheelchair center of gravity (adjusting seat depth or back height,

adding or removing a powered seating option, etc.) then it is necessary to check the stability lock adjustment. Refer to Adjusting the

Stability Lock Setting on page 53.

Adult Size Seats

NOTE: For this procedure, refer to FIGURE 8.1 on page 55.

Removing

1.

Remove seating system and seat pan.

2.

Remove the eight 5/16-18 X 3/4 socket head screws, 11/32 X 13/16 X 3/4 ground washers and four 5/16-18 plates that
secure the seat frame to the base frame.

3.

Lifting up, remove the seat assembly from the base frame.

Installing

1.

Position the seat assembly onto the base frame.

2.

Using the eight 5/16-18 X 3/4 socket head screws, 11/32 X 13/16 X 3/4 ground washers and four 5/16-18 plates, secure the
seat frame to the base frame. Torque to 13 ft-lbs ± 20%.

3.

Remove seating system and seat pan.

FIGURE 8.1

Removing/Installing Seat - Adult Size Seats

11/32 X 13/16 X 3/4

Ground Washers

6/16-18 Plates

Seat Frame

Base Frame

5/16-18 X 3/4 Socket

Head Screws

«
...
53
54
55
56
57
...
»

Содержание TDX-SP N

























































































Отзывы:

Нет отзывов

Похожие инструкции для TDX-SP N

Бренд: Felco Страницы: 20

Бренд: Meyra Страницы: 104

Бренд: Invacare Страницы: 36

ZT-600-710-SP16

Бренд: Z-Tec Страницы: 7

Бренд: Motion Composites Страницы: 40

Бренд: CHEELCARE Страницы: 33

Бренд: Quantum Rehab Страницы: 55

Бренд: panthera Страницы: 5

Бренд: R82 Страницы: 12

NUVO GLIDEABOUT MOBILE COMMODE

Бренд: NRS Страницы: 2

Бренд: Vermeiren Страницы: 7

Бренд: Gate Страницы: 8

Mobilex Dolphin MEM6443P

Бренд: Decon wheel Страницы: 3

Бренд: Days Страницы: 12

Бренд: aidapt Страницы: 3

Posi-Pro Wheelchair Cushion

Бренд: SafeLife Страницы: 13

Mini Tilt Wheelchair

Бренд: Tendercare Страницы: 28

Бренд: Peak Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды