Invacare TDX-SP N Скачать руководство пользователя | Manualshive

Страница: 65 / 88

background image

SECTION 9—BATTERIES

Part No 1143209

65

Replacing Batteries

NOTE: For this procedure, refer to FIGURE 9.1 on page 66.

NOTE: The following tools are required to perform this procedure:

•

Wire Cutter

1.

Remove the batteries from the wheelchair. Refer to Removing/Installing the Batteries From/Into the Wheelchair on
page 67.

2.

Cut the tie-wraps that secure the battery terminal covers to the battery terminals.

3.

Slide the RED battery terminal cover back on the RED battery cable to expose the POSITIVE battery terminal.

4.

Slide the BLACK battery terminal cover back on the BLACK battery cable to expose NEGATIVE battery terminal.

DANGER

Risk of Death or Serious Injury
Failure to observe these warnings can cause an electrical short resulting in death, serious injury,

or damage to the electrical system.
The POSITIVE (+) RED battery cable MUST connect to the POSITIVE (+) battery

terminal(s)/post(s).
The NEGATIVE (-) BLACK battery cable MUST connect to the NEGATIVE (-) battery

terminal(s)/post(s).
NEVER allow any of your tools and/or battery cable(s) to contact BOTH battery post(s) at the

same time. An electrical short may occur and serious injury or damage may occur.
Install protective caps on positive and negative battery terminals.
Replace cable(s) immediately if cable(s) insulation becomes damaged.
DO NOT remove fuse or mounting hardware from POSITIVE (+) red battery cable mounting

screw.

5.

Remove the locknut that secures the bracket of the POSITIVE battery cable to the POSITIVE (+) battery post of the
battery.

6.

Remove the locknut that secures the NEGATIVE battery cable to the NEGATIVE(-) battery post of the battery

7.

Discard the existing battery.

8.

Position battery connector bracket or wiring harness onto the new 22NF or GP24 battery as shown.

9.

Secure the NEGATIVE battery cable to the NEGATIVE (-) battery post with existing mounting screw and locknut.

10. Secure the bracket of the POSITIVE battery cable to the POSITIVE (+) battery post with existing mounting screw and

locknut.

11. Position each battery terminal cover over top of each battery terminal.

12. Secure battery terminal covers in place with one tie-wrap.

13. Install batteries into wheelchair. Refer to Removing/Installing the Batteries From/Into the Wheelchair on page 67.

«
...
63
64
65
66
67
...
»

Содержание TDX-SP N

























































































Отзывы:

Нет отзывов

Похожие инструкции для TDX-SP N

Бренд: Handicare Страницы: 32

Бренд: Motion Concepts Страницы: 88

Бренд: Decon wheel Страницы: 4

Бренд: Jay Страницы: 32

Бренд: Pride Страницы: 39

Бренд: Pride Страницы: 36

Quantum Q6 Edge

Бренд: Pride Страницы: 44

Quantum litestream junior

Бренд: Pride Страницы: 43

Quantum 06 edge va

Бренд: Pride Страницы: 36

Quantum 6000Z Series

Бренд: Pride Страницы: 40

Бренд: Pride Страницы: 44

Бренд: Pride Страницы: 40

Бренд: XXL-Rehab Страницы: 8

Бренд: TA Service Страницы: 50

Бренд: Rehab Страницы: 2

WHEELCHAIR Series

Бренд: Paravan Страницы: 160

Бренд: Quickie Страницы: 36

Бренд: RGK Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды