Invacare TDX-SP N Скачать руководство пользователя | Manualshive

Страница: 41 / 88

background image

SECTION 5—MOTORS

Part No 1143209

41

Aligning the SSD Motor to the Gearbox

1.

If adjusting an assembled motor/gearbox, loosen the square neck bolt, spacer, washer and locknut securing the band
clamp to the motor/gearbox assembly.

2.

Align the motor to the gearbox according to the table below:

3.

If adjusting an assembled motor/gearbox, securely tighten the square neck bolt, spacer, washer and locknut. Torque
locknut to 75 in-lbs ± 10%.

Installing the SSD Brake Lever

NOTE: For this procedure, refer to FIGURE 5.3.
NOTE: Brake levers are right and left side specific. Brake levers
MUST mount to the brake lever post as described in STEP 2 and
shown in FIGURE 5.3 to ensure the proper brake lever has been
mounted to the correct motor.

1.

Locate the brake lever post on the end of the motor
opposite the gearbox.

2.

Align the brake lever with the brake lever post so that:
•

The brake lever handle will be positioned towards
the outside of the wheelchair.

•

The set screw will tighten against the flat space of
the brake lever post.

•

The cut out on the bottom edge of the brake lever
will fit around the brake lever stop.

3.

Securely tighten the set screw securing the brake lever
to the brake lever post.

4.

If necessary, perform STEPS 1-3 to install the remaining
brake lever.

FIGURE 5.3

Installing the SSD Brake Lever

Installing the SSD Motor Push/Drive Label

NOTE: For this procedure, refer to FIGURE 5.4.

1.

Peel the label from the adhesive backing.

2.

Position the label on the motor near the brake lever as
shown.

3.

If necessary, repeat STEPS 1-2 for opposite motor to
install the remaining push/drive label.

FIGURE 5.4

Installing the SSD Motor Push/Drive Label

WHEELCHAIR

LEFT SIDE

RIGHT SIDE

TDX SP - 4 POLE

180° Indicator Mark

(Motor)

Indicator Mark (Gearbox)

Indicator Mark (Gearbox)

0° Indicator Mark

(Motor)

Outside of

Wheelchair

Brake Lock Lever (Handle)

Cutout

Set Screw

Brake Lever Post

Brake Lever

Stop

Outside of

Wheelchair

Brake Lock Lever (Handle)

Cutout

Set Screw

Brake Lever Post

Brake Lock
Lever Stop

Right Side Motor

Left Side Motor

NOTE: Right side motor shown, use same
location for left side motor.

Position

Push/Drive

Label HERE

«
...
39
40
41
42
43
...
»

Содержание TDX-SP N

























































































Отзывы:

Нет отзывов

Похожие инструкции для TDX-SP N

Бренд: Invacare Страницы: 40

Бренд: Otto Bock Страницы: 36

Бренд: Ki Mobility Страницы: 96

Synergy Shape Back

Бренд: Quantum Rehab Страницы: 20

Бренд: TiLite Страницы: 119

Бренд: Levo Страницы: 25

Бренд: Levo Страницы: 52

Бренд: Handicare Страницы: 24

Бренд: Quickie Страницы: 106

Бренд: Zippie Страницы: 36

Бренд: Quickie Страницы: 80

Бренд: Zitzi Страницы: 40

Бренд: KYMCO Страницы: 37

Бренд: Motion Composites Страницы: 24

Active Rigid Frame Wheelchair

Бренд: motivation Страницы: 37

Бренд: Motion Composites Страницы: 2

Бренд: Motion Composites Страницы: 24

Бренд: Motion Composites Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды