Invacare TDX-SP N Скачать руководство пользователя | Manualshive

Страница: 74 / 88

background image

SECTION 10—ELECTRONICS

74

Part No 1143209

SECTION 10—ELECTRONICS

Controller Calibration

NOTE: For this procedure, refer to FIGURE 10.1.

1.

Connect the programer to the charger/programming port.

2.

Refer to MK6 electronics programing guide part number 1141471 for controller calibration information.

FIGURE 10.1

Controller Calibration

Removing/Installing the Controller

NOTE: For this procedure, refer to FIGURE 10.2 on page 75.

Removing

1.

Wheelchairs with TRRO, TRBKTS, or powered Seating System Installed ONLY: Remove the four 5/16-18 X 5/8 socket head
cap screws and secure the pivot cross-member to the two rear swingarms (Detail “A”).

2.

Remove the rear shroud. Refer to Adjusting the Formula CG Seating System Mounting Position on page 58.

3.

Disconnect the right and left motors form the controller.

4.

Disconnect the joystick cable from the controller.

5.

Disconnect the battery cable from the controller.

6.

Lift the controller up until the two 9/16 ID X 1-1/16 OD X 3/8-inch washers release from the base frame.

7.

Pull the controller away to remove the controller from the wheelchair frame.

8.

If necessary to replace the controller mounting hardware, perform the following:

A. Remove the two 8-32 X 1.00-inch pan head screws and 8-32 locknuts that secure the controller mounting washers and

9/16 ID X 1-1/16 OD X 3/8-inch washers to the controller.

B. Remove the two controller mounting washers from the two 9/16 ID X 1-1/16 OD X 3/8 inch washers.

Installing

1.

If necessary to install the controller mounting hardware, perform the following:

A. Insert the two controller mounting washers into two 9/16 ID X 1-1/16 OD X 3/8-inch washers.
B. using the two 8-32 X 1.00-inch pan head screws and 8-32 locknuts, secure the controller mounting washers and 9/16 ID X

1-1/16 OD X 3/8 inch washers to the controller.

2.

Align the two 9/16 ID X 1-1/16 OD X 3/8-inch washers of the controller with the two large openings of the base frame.

3.

Insert the two 9/16 ID X 1-1/16 OD X 3/8-inch washers into the two large openings of the base frame and push down until the
controller is securely locked into position.

4.

Connect the battery cable from the controller.

MPJ Joystick

Charger/Programming Port

(On front of Joystick)

«
...
72
73
74
75
76
...
»

Содержание TDX-SP N

























































































Отзывы:

Нет отзывов

Похожие инструкции для TDX-SP N

Бренд: R82 Страницы: 7

Бренд: R82 Страницы: 5

iChair DYNAMIC 1.623

Бренд: Meyra Страницы: 64

Бренд: Everest & Jennings Страницы: 32

Бренд: Invacare Страницы: 107

Kanga 1300-921110

Бренд: Inspired by drive Страницы: 8

Expedition Plus

Бренд: Drive Страницы: 12

Бренд: Pride Страницы: 42

Бренд: Pride Страницы: 59

Бренд: Quickie Страницы: 44

Бренд: Ti Lite Страницы: 147

Бренд: Barrett Страницы: 44

Compass HD GP620 CC

Бренд: Golden Страницы: 39

Бренд: Golden Страницы: 46

Бренд: Jay Страницы: 148

Бренд: Innovate Страницы: 18

Бренд: Falcon Страницы: 63

Бренд: AAT Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды