Invacare TDX-SP N Скачать руководство пользователя

Страница: 23 / 88

SECTION 3—SAFETY INSPECTION/TROUBLESHOOTING

Part No 1143209

TDX® SP

Information Gauge Display Diagnostics

Service Indicator Light Diagnostics

DISPLAY

DESCRIPTION

DEFINITION

COMMENTS

All LEDs are off.

Power is off.

All LEDs are on.

Power is on.

Fewer than three LEDs on implies
reduced battery charge.

Left RED LED is flashing.

Battery charge is low.

The batteries should be charged
as soon as possible.

Left to Right “chase”
alternating with steady display.

Joystick is in programming,
inhibit and/or charging mode.

The steady LEDs indicate the
current state of the battery
charge.

All LEDs are flashing slowly.

Joystick has detected Out- of-
Neutral-at-Power-Up mode.

Release the joystick to Neutral.

NUMBER OF FLASHES

DIAGNOSTICS CODE

ERROR CODE DESCRIPTION

SUB CO

DE*

DETAILS OF ERROR CODE

POSSIBLE SO

LUT

ION

E 01

User Fault

Stall Timeout or user error.

Release joystick to neutral and try again.

E02

Battery Fault

Recharge batteries or replace.

Check the batteries and cable. Try charging the
batteries. Batteries may require replacing.

Information

Gauge

Display

Содержание TDX-SP N

























































































Результаты поиска

Содержание TDX-SP N

Отзывы:

Похожие инструкции для TDX-SP N

Бренды по названию

Популярные бренды

Invacare TDX-SP N, Руководство по обслуживанию

Результаты поиска

Содержание TDX-SP N

Отзывы:

Похожие инструкции для TDX-SP N

Бренды по названию

Популярные бренды