Invacare TDX-SP N Скачать руководство пользователя | Manualshive

Страница: 80 / 88

background image

SECTION 11—TRANSPORT IN VEHICLES

80

Part No 1143209

WARNING!

Risk of Injury, Damage or Death
Lack or improper use of wheelchair transport systems may result in injury, damage or death.
– Use both pelvic and upper torso belts.
– The pelvic belt that is provided by Invacare has been tested for use in a motor vehicle on this

wheelchair only. Do not replace the pelvic belt with a different style pelvic belt.

NOTE: ANSI = American National Standards Institute, RESNA=Rehabilitation Engineering and Assistive Technology Society of
North America.

TRRO includes four factory-installed transport brackets and a wheelchair anchored pelvic belt.
•

The wheelchair has been tested for seating in a motor vehicle with the factory installed seating system only.

•

This wheelchair has been dynamically tested in a forward-facing mode with the specified crash test dummy restrained
by BOTH pelvic and upper-torso belt(s) (shoulder belts), and that BOTH pelvic and upper torso belt(s) should be used
to reduce the possibility of head an chest impacts with vehicle components.

•

TRRO has been crash-tested in accordance with ANSI/RESNA WC Vol 1 Section 19 Frontal Impact Test requirements for

•

wheelchairs with a 130 lb (59 kg) crash test dummy, which corresponds to a person with a weight of 125 lb (57 kg) to 165

•

lb (75 kg) for Junior seat sizes or a 168 lb (76 kg) crash dummy, which corresponds to a person with a weight of 165 lb
(75 kg) to 300 lbs (136 kg) for Adult seat sizes.

Compliance Information

This wheelchair conforms with the requirements of the ANSI/RESNA WC/Vol. 1 - Section 19.

NOTE: ANSI = American National Standards Institute, RESNA= Rehabilitation Engineering and Assistive Technology Society of North
America.

This wheelchair has been dynamically tested in a forward-facing mode with the specified crash test dummy, which corresponds

to a person with a weight of 114-209 pounds, restrained by BOTH pelvic and upper-torso belts in accordance with ANSI/RESNA

WC Vol 1 Section 19. BOTH pelvic and upper-torso belts should be used to reduce the possibility of head and chest impacts with

vehicle components.

Specifications

MODEL

MOTOR

WHEELCHAIR WEIGHT LIMIT

ADULT

JUNIOR

TDX SP HD

4 Pole HD

Up to 400 pounds

Up to 150 pounds

TDX SP

4 Pole

Up to 300 pounds

Up to 150 pounds

«
...
78
79
80
81
82
...
»

Содержание TDX-SP N

























































































Отзывы:

Нет отзывов

Похожие инструкции для TDX-SP N

Guardian Escort

Бренд: Sunrise Medical Страницы: 34

esprit action4 NG

Бренд: Invacare Страницы: 32

Бренд: Shoprider Страницы: 2

Cobi Cruise Power

Бренд: Cobi Rehab Страницы: 16

Бренд: Quantum Страницы: 20

Бренд: Quantum Rehab Страницы: 59

Бренд: Quantum Страницы: 48

HD Balance 62471

Бренд: HD Rehab Страницы: 2

Бренд: Koh-I-Noor Страницы: 2

Бренд: Quantum Страницы: 51

Бренд: Jay Страницы: 32

Бренд: EZee Life Страницы: 19

Бренд: ROHO Страницы: 10

AGILITY AG-LATFX-L-FL

Бренд: ROHO Страницы: 18

Бренд: Innovate Страницы: 18

Бренд: You-Q Страницы: 57

Бренд: Handicare Страницы: 40

Бренд: Xsensor Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды