Invacare TDX-SP N Скачать руководство пользователя | Manualshive

Страница: 36 / 88

background image

SECTION 4—WHEELS AND WHEEL LOCKS

36

Part No 1143209

Adjusting Caster Fork Assemblies

NOTE: For this procedure, refer to FIGURE 4.4.

NOTE: Front and rear caster assemblies are adjusted in the same manner.

NOTE: A #10-32 X 11/16-inch Phillips head screw is used to secure the front head tube cap to the front head tube. A #10-16 X 3/8-inch
phillip pan head drill screw secures the rear head tube cap to the rear head tube.

1.

Remove the mounting screw securing the head tube cap to the head tube.

2.

To properly tighten caster fork assembly and guard against flutter, perform the following check:

NOTE: Two people are recommended to perform the following procedure - one to tip wheelchair back and one to inspect/adjust the caster
assembly.

A. Tip back the wheelchair.

B.

Pivot both caster assemblies to top of their arc simultaneously.

C.

Let casters drop to bottom of arc (casters should swing once to one-side, then immediately rest in a straight downward position).

D. Adjust 5/8-1/8-inch locknuts according to freedom of caster swing.

3.

Test the wheelchair maneuverability.

4.

Adjust 5/8-1/8-inch locknuts if necessary, and repeat STEPS 2-3 until correct.

5.

Position the head tube cover onto the top of the head tube.

6.

Using the mounting screw, secure the head tube cap to the head tube.

FIGURE 4.4

Adjusting Caster Fork Assemblies

Removing/Installing the Caster Fork Assemblies

NOTE: For this procedure, refer to FIGURE 4.5 on page 37.

NOTE: Front and rear caster assemblies are replaced in the same manner.

NOTE: A #10-32 X 11/16-inch Phillips head screw is used to secure the front head tube cap to the front head tube. A #10-16 X 3/8-inch
phillip pan head drill screw secures the rear head tube cap to the rear head tube.

Removing

1.

Remove the mounting screw securing the head tube cap to the head tube.

2.

Remove the 5/8-1/8 locknut and 5/8 X 1-5/16 X 1/8 inch washer and 5/8 X 1-1/8 X 3/16 inch stem spacer from the threaded
post securing the caster fork assembly to the headtube.

3.

If necessary, remove the two bearings and tolerance rings from the head tube.

Fork

Mounting Screw

Head Tube

5/8-1/8-inch Locknut

Head Tube Cover

«
...
34
35
36
37
38
...
»

Содержание TDX-SP N

























































































Отзывы:

Нет отзывов

Похожие инструкции для TDX-SP N

ICON BACK SYSTEM

Бренд: VARILITE Страницы: 20

Бренд: Quickie Страницы: 44

Бренд: progeo Страницы: 3

Бренд: C.T.M. Страницы: 20

Бренд: Roma Medical Страницы: 27

Бренд: Permobil Страницы: 2

Бренд: Hoggi Страницы: 41

Бренд: LEADING CHAIR Страницы: 2

Бренд: UCP Страницы: 14

Бренд: Redgum Страницы: 16

Бренд: Marvel Страницы: 47

Бренд: Otto Bock Страницы: 64

Бренд: I-GO Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды