manualshive.com logo in svg

Intel SE7520BD2, Технические характеристики продукции, Страница: 132 / 179

Поделиться
Скачать
Intel SE7520BD2 Скачать руководство пользователя страница 132

Error Reporting and Handling 

Intel® Server Board SE7520BD2 Technical Product Specification 

120  

Revision 

1.3 

 

 

Table 57.  POST Error Beep Codes 

Number of Beeps 

Description 

1  

Memory refresh timer error. 

3  

Main memory read / write test error. 

6  

Keyboard controller BAT test error. 

 

Table 58.  Troubleshooting BIOS Beep Codes

 

 

 

Number of Beeps  

Troubleshooting Action  

1, 2 or 3  

Reseat the memory, or replace with known good modules.  

4-7, 9-11  

Fatal error indicating a serious problem with the system. 
Consult your system manufacturer.  
Before declaring the motherboard beyond all hope, 
eliminate the possibility of interference by a malfunctioning 
add-in card. Remove all expansion cards except the video 
adapter.  
- If the beep codes are generated even when all other 
expansion cards are absent, the motherboard has a serious 
problem. Consult your system manufacturer.  
- If the beep codes are not generated when all other 
expansion cards are absent, one of the add-in cards is 
causing the malfunction. Insert the cards back into the 
system one at a time until the problem happens again. This 
will reveal the malfunctioning add-in card.  

8  

If the system video adapter is an add-in card, replace or 
reseat the video adapter. If the video adapter is an 
integrated part of the system board, the board may be 
faulty.  

 

5.3.3 Checkpoints 

5.3.3.1 

System ROM BIOS POST Task Test Point (Port 80h Code) 

The BIOS will send a 1-byte hex code to the port 80 before each task. 

The port 80 codes provide a troubleshooting method in the event of a system hang during 
POST 

The value of port 80h will be sent to four tri-color LEDs. This diagnostic LED feature consists of 
a hardware decoder and four dual-color LEDs located on the baseboard.  During POST, the 
LEDs display all normal POST progress codes representing the progress of the BIOS POST.  
Each code is represented by a combination of colors from the four LEDs.  The LEDs are in pairs 
of green and red.  The POST progress codes are broken into two nibbles, an upper and a lower 
nibble.  Each bit in the upper nibble is represented by a red LED; each bit in the lower nibble is 
represented by a green LED.  If both bits are set in the upper and lower nibble then both red 
and green LEDs are lit, resulting in an amber color.  Likewise, if both bits are clear then both the 
red and green LEDs are off. 

In the following example, the BIOS sends a value of ACh to the LEDs.  The LEDs are decoded 
as follows: 

Содержание SE7520BD2




















































































































































































Отзывы:

Нет отзывов