Intel Celeron Dual-Core E1000 Series Скачать руководство пользователя страница 96

Страница: 96 / 148

Case Temperature Reference Metrology

Thermal and Mechanical Design Guidelines

Figure

7-17. Bending the Tip of the Thermocouple

D.5.2

Thermocouple Attachment to the IHS

12.

Clean groove and IHS with Isopropyl Alcohol (IPA) and a lint free cloth removing

all residues prior to thermocouple attachment.

13.

Place the thermocouple wire inside the groove; letting the exposed wire and bead

extend about 1.5 mm [0.030 inch] past the end of groove. Secure it with Kapton*
tape (Figure

7-18). Clean the IHS with a swab and IPA.

14.

Verify under the microscope that the thermocouple wires are straight and parallel

in the groove and that the bead is still bent.

Figure

7-18. Securing Thermocouple Wires with Kapton* Tape Prior to Attach

15.

Lift the wire at the middle of groove with tweezers and bend the front of wire to

place the thermocouple in the groove ensuring the tip is in contact with the end
and bottom of the groove in the IHS (Figure

7-19-A and B).

Содержание Celeron Dual-Core E1000 Series





















































































































































Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды

Intel Celeron Dual-Core E1000 Series, Руководство по дизайну

Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды