Intel Celeron Dual-Core E1000 Series Скачать руководство пользователя страница 118

Страница: 118 / 148

Legacy Fan Speed Control

118

Thermal and Mechanical Design Guidelines

Table

7-4. ATX FSC Settings

Parameter Classification

Processor

Thermal

Sensor

PWM Output

Notes

HIGH

Required

CONTROL

LOW

Required

CONTROL

– 10 °C

3,5

Minimum PWM Duty
Cycle

Required

20%

PWM Frequency

Required

21–28

kHz

Spin-up time

Suggested

250 – ~500 ms

2, 6

AVERAGING

Suggested

sec 6

When T

SENSOR

< T

LOW

Suggested Minimum

PWM%

All Fans ON

Suggested

CONTROL

+ 3 °C

Hysteresis Suggested

°C

Offset Required

Thermal

Diode

Correction Factor

NOTES:

A PWM frequency of 25 kHz is the design target for the reference and for the Intel

Boxed Processor and the reference design.

Use the lowest time available in this range for the device selected.

To ensure compliance with the thermal specification, thermal profile and usage of the

SENSOR

for fan speed control these setting should not be user configurable.

If present in the FSC device the Thermal Diode Correction Factor should be input to this

If the FSC device does not have a means to input a fixed temperature offset then:

HIGH

CONTROL

+ Thermal Diode Correction Factor and

LOW

CONTROL

+ Thermal Diode Correction Factor.

If this function is present on the device it must be enabled

Содержание Celeron Dual-Core E1000 Series





















































































































































Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды

Intel Celeron Dual-Core E1000 Series, Руководство по дизайну

Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды