Intel Celeron Dual-Core E1000 Series Скачать руководство пользователя страница 101

Страница: 101 / 148

Case Temperature Reference Metrology

Thermal and Mechanical Design Guidelines

101

Figure

7-26. Positioning Solder on IHS

23.

Measure the resistance from the thermocouple end wires again using the DMM
(refer to Section

D.5.1.step 2) to ensure the bead is still properly contacting the

IHS.

D.5.3

Solder Process

24.

Make sure the thermocouple that monitors the Solder Block temperature is

positioned on the Heater block. Connect the thermocouple to a handheld meter to

monitor the heater block temperature.

25.

Verify the temperature of the Heater block station has reached 155 °C ±5 °C

before you proceed.

26.

Connect the thermocouple for the device being soldered to a second hand held

meter to monitor IHS temperature during the solder process.

Содержание Celeron Dual-Core E1000 Series





















































































































































Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды

Intel Celeron Dual-Core E1000 Series, Руководство по дизайну

Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды