Intel Celeron Dual-Core E1000 Series Скачать руководство пользователя страница 71

Страница: 71 / 148

Intel® Quiet System Technology (Intel® QST)

Thermal and Mechanical Design Guidelines

target temperature. As a result of its operation, the PID control algorithm can enable

an acoustic-friendly platform.

Figure

7-2. PID Controller Fundamentals

Proportional
Error

Derivative (Slope)

Integral (time averaged)

Proportional
Error

Derivative (Slope)

Integral (time averaged)

Proportional
Error

Derivative (Slope)

Integral (time averaged)

Proportional
Error

Derivative (Slope)

Integral (time averaged)

RPM

Tempera

ture

Time

+ dPW

+ d

+ dPW

+ d

+ dPW

+ d

Actual

Temperature

Actual

Temperature

Fan

Speed

Fan

Speed

Limit
Temperature

For a PID algorithm to work limit temperatures are assigned for each temperature

sensor. For Intel QST, the T

CONTROL

for the processor and chipset are to be used as the

limit temperature. The ME will measure the error, slope and rate of change using the

following equations:

•

Proportional Error (P) = T

LIMIT

– T

ACTUAL

•

Integral (I) = Time averaged error

•

Derivative (D) =

Temp /

Time

Three gain values are used to control response of algorithm.

•

Kp = proportional gain

•

Ki = Integral gain

•

Kd = derivative gain

The Intel

Quiet System Technology (Intel

QST) Configuration and Tuning Manual

provides initial values for the each of the gain constants. In addition it provides a

methodology to tune these gain values based on system response.

Finally the fan speed change will be calculated using the following formula:

PWM = -P*(Kp) – I*(Ki) + D*(Kd)

Содержание Celeron Dual-Core E1000 Series





















































































































































Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды

Intel Celeron Dual-Core E1000 Series, Руководство по дизайну

Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды