Intel Celeron Dual-Core E1000 Series Скачать руководство пользователя страница 82

Страница: 82 / 148

Heatsink Clip Load Metrology

Thermal and Mechanical Design Guidelines

Remarks: Alternate Heatsink Sample Preparation

As mentioned above, making sure that the load cells have minimum protrusion out of

the heatsink base is paramount to meaningful results. An alternate method to make

sure that the test setup will measure loads representative of the non-modified design

is:

•

Machine the pocket in the heat sink base to a depth such that the tips of the load

cells are just flush with the heat sink base

•

Then machine back the heatsink base by around 0.25 mm [0.01”], so that the

load cell tips protrude beyond the base.

Proceeding this way, the original stack height of the heatsink assembly should be

preserved. This should not affect the stiffness of the heatsink significantly.

Figure

7-8. Load Cell Installation in Machined Heatsink Base Pocket – Bottom View

Package IHS

Outline (Top

Surface)

Load Cells

Heatsink Base Pocket

Diameter ~ 29 mm

[~1.15”]

Содержание Celeron Dual-Core E1000 Series





















































































































































Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды

Intel Celeron Dual-Core E1000 Series, Руководство по дизайну

Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды