Intel Celeron Dual-Core E1000 Series Скачать руководство пользователя страница 55

Страница: 55 / 148

ATX Thermal/Mechanical Design Information

Thermal and Mechanical Design Guidelines

ATX Thermal/Mechanical
Design Information

6.1

ATX Reference Design Requirements

This chapter will document the requirements for an active air-cooled design, with a

fan installed at the top of the heatsink. The thermal technology required for the

processor.

The processors of Intel

Core

™

2 Duo processor with 4 MB cache at Tc-max of 60.1 °C,

Intel

Core

™

2 Duo processor with 2 MB cache at Tc-max of 61.4 °C and Intel

Pentium

Dual Core processor E2000 series at Tc-max of 61.4 °C require a thermal

solution equivalent to the D60188-001 reference design, see Figure

6-1 for an

exploded view of this reference design.

Note:

The part number D60188-001 provided in this document is for reference only. The
revision number -001 may be subject to change without notice.

The D60188-001 reference design takes advantage of an acoustic improvement to

reduce the fan speed to show the acoustic advantage (its acoustic results show in the
Table

6-3).

The D60188-001 reference design takes advantage of the cost saving for the light

fan/heatsink mass (450g) and the new TIM material (Dow Corning TC-1996 grease). A
bottom view of the copper core applied by this grease is provided Figure

6-3.

Содержание Celeron Dual-Core E1000 Series





















































































































































Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды

Intel Celeron Dual-Core E1000 Series, Руководство по дизайну

Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды