Intel Celeron Dual-Core E1000 Series Скачать руководство пользователя страница 84

Страница: 84 / 148

Heatsink Clip Load Metrology

Thermal and Mechanical Design Guidelines

B.2.2

Typical Test Equipment

For the heatsink clip load measurement, use equivalent test equipment to the one
listed Table

7-2.

Table

7-2. Typical Test Equipment

Item

Description

Part Number

(Model)

Load cell

Notes: 1, 5

Honeywell*-Sensotec* Model 13 subminiature
load cells, compression only

Select a load range depending on load level
being tested.

www.sensotec.com

AL322BL

Data Logger (or
scanner)

Notes: 2, 3, 4

Vishay* Measurements Group Model 6100
scanner with a 6010A strain card (one card
required per channel).

Model 6100

NOTES:

Select load range depending on expected load level. It is usually better, whenever

possible, to operate in the high end of the load cell capability. Check with your load cell

vendor for further information.

Since the load cells are calibrated in terms of mV/V, a data logger or scanner is

required to supply 5 volts DC excitation and read the mV response. An

automated model will take the sensitivity calibration of the load cells and convert the

mV output into pounds.

With the test equipment listed above, it is possible to automate data recording and

control with a 6101-PCI card (GPIB) added to the scanner, allowing it to be connected

to a PC running LabVIEW* or Vishay's StrainSmart* software.

IMPORTANT: In addition to just a zeroing of the force reading at no applied load, it is

important to calibrate the load cells against known loads. Load cells tend to drift.

Contact your load cell vendor for calibration tools and procedure information.

When measuring loads under thermal stress (bake for example), load cell thermal

capability must be checked, and the test setup must integrate any hardware used along

with the load cell. For example, the Model 13 load cells are temperature compensated

up to 71 °C, as long as the compensation package (spliced into the load cell's wiring) is

also placed in the temperature chamber. The load cells can handle up to 121 °C

(operating), but their uncertainty increases according to 0.02% rdg/°F.

B.3

Test Procedure Examples

The following sections give two examples of load measurement. However, this is not

meant to be used in mechanical shock and vibration testing.

Any mechanical device used along with the heatsink attach mechanism will need to be

included in the test setup (i.e., back plate, attach to chassis, etc.).

Prior to any test, make sure that the load cell has been calibrated against known

loads, following load cell vendor’s instructions.

Содержание Celeron Dual-Core E1000 Series





















































































































































Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды

Intel Celeron Dual-Core E1000 Series, Руководство по дизайну

Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды