Intel Celeron Dual-Core E1000 Series Скачать руководство пользователя страница 117

Страница: 117 / 148

Legacy Fan Speed Control

Thermal and Mechanical Design Guidelines

117

Figure

7-44. FSC Definition Example

Requirements Classification

•

Required – an essential part of the design necessary to meet specifications.

Should be considered a pass or fail in selection of a board.

•

Suggested – highly desired for consistency among designs. May be specified or

expanded by the system integrator.

The motherboard needs to have a fan speed control component that has the following

characteristics:

•

PWM output programmable to 21–28 kHz (required). PWM output set to 25 kHz

(Suggested) as this value is the design target for the reference and for the Boxed

Processor.

•

External/remote thermal sensor measurement capability (required). Must support

PECI and thermal diode using a SST device

•

External/remote thermal sensor sampling rate

≥

4 times per second (required).

•

External/remote diode measurement (SST device) is calibrated by the component

vendor to account for the diode ideality and package series resistance as listed in

the appropriate datasheet. (Suggested).

Note:

If the SST thermal sensor is not calibrated with the diode ideality and package series
resistance, verify the board manufacturer has made provisions within the BIOS setup
or other utility to input the corrections factors.

The BIOS, at a minimum, must program the settings in Table

7-4 or Table

7-5, as

appropriate, into the fan speed controller. The values are the minimum required to

establish a fan speed control algorithm consistent with this document, the reference

thermal solution and Boxed Processor thermal solution.

Содержание Celeron Dual-Core E1000 Series





















































































































































Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды

Intel Celeron Dual-Core E1000 Series, Руководство по дизайну

Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды