Intel Celeron Dual-Core E1000 Series Скачать руководство пользователя страница 66

Страница: 66 / 148

ATX Thermal/Mechanical Design Information

Thermal and Mechanical Design Guidelines

6.7.2

Mechanical Interface to the Reference Attach Mechanism

The attach mechanism component from the reference design can be used by other 3

party cooling solutions. The attach mechanism consists of:

•

A metal attach clip that interfaces with the heatsink core, see

Appendix H,

Figure

7-55 and Figure

7-56 for the component drawings.

•

Four plastic fasteners, see

7-60 for the component drawings.

The clip is assembled to heatsink during copper core insertion, and is meant to be
trapped between the core shoulder and the extrusion as shown in Figure

6-7.

Figure

6-7. Reference Clip/Heatsink Assembly

Core shoulder
traps clip in place

Clip

The mechanical interface with the reference attach mechanism is defined in Figure

6-8

and Figure

6-9. Complying with the mechanical interface parameters is critical to

generating a heatsink preload compliant with the minimum preload requirement given
in Section

2.1.2.2.

Additional requirements for the reference attach mechanism (clip and fasteners)

include:

•

Heatsink/fan mass

≤

550 g (i.e., total assembly mass, including clip and fasteners

< 595 g

•

Whole assembly center of gravity

≤

25.4 mm, measured from the top of the IHS

⎯

Whole assembly = He Fan + Attach clip + Fasteners

Содержание Celeron Dual-Core E1000 Series





















































































































































Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды

Intel Celeron Dual-Core E1000 Series, Руководство по дизайну

Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды